HVAC & Plumbing Services in University Heights

Responded to water heater failure resulting in significant basement flooding. Upon arrival, found extensive water accumulation on concrete floor with dark staining indicating prolonged moisture exposure. Deployed portable vacuum pump with drainage hoses to extract standing water from affected area. Connected discharge lines to floor drain for proper water removal. Coordinated with HVAC technician scheduled for same-day service to address air conditioning system following water heater assessment. Water heater exhibited signs of tank failure requiring immediate attention to prevent further flooding damage.

Responded to gas line repair request at a 70-year-old residential property. Successfully located and repaired compromised gas line connection within HVAC mechanical housing, replaced worn flexible gas connector, and conducted pressure test to verify system integrity and confirm no leaks present.

Responded to water leak concern at exterior panels suspected to originate from AC condensate drainage system. Upon inspection, discovered significant water damage and deterioration in basement/crawl space area with compromised wall surfaces, peeling paint, and exposed brickwork. Examined PVC drainage pipes, condensate lines, and associated plumbing infrastructure running along walls and overhead. Documented existing conditions showing white stone drainage bed with debris accumulation, multiple pipe runs including insulated refrigerant lines, copper piping, and flexible conduit installations. Assessed integrity of condensate drain system and mounting hardware. Photographed deteriorated wall conditions, pipe routing, and overhead utility infrastructure for documentation purposes.

Responded to service call for garbage disposal leak beneath kitchen sink. Upon inspection, identified small leak at disposal mounting flange connection to sink basin. Tightened mounting bolts and inspected drain connections, including corrugated drain hose and PVC discharge pipe assembly. Verified proper sealing of all connections, tested disposal operation, and confirmed leak was resolved with no further water discharge observed.

Replaced three steam valves servicing the kitchen and bathroom radiators, and installed a new steam vent on the living room radiator. All components were tested and verified for proper operation. System is functioning correctly with no leaks detected.

Completed comprehensive plumbing stack assessment and repair work involving sump pump system and exterior spigot connections over a four-day period with two-person crew. Performed exploratory demolition of interior wall and ceiling sections to access concealed plumbing infrastructure, exposing vertical stack assembly, supply lines, and drainage components. Documented extensive water damage and deterioration to wall framing and drywall materials, indicating previous moisture intrusion requiring remediation prior to system repairs and wall restoration.

Conducted on-site assessment for multi-story residence currently equipped with boiler system and furnace/AC serving main floor only. Evaluated heating and cooling requirements for unserved second and third floor areas, inspecting existing mechanical infrastructure and available installation pathways. Documented current HVAC configuration including exposed ductwork and equipment locations in upper level spaces. Provided professional recommendations comparing heat pump system versus alternative HVAC solutions for upper floor climate control, discussing zoning options to integrate with existing first-floor equipment while maintaining independent temperature control for each level.

Performed comprehensive maintenance on steam boiler system of unknown age. Inspected burner assembly, gas valve components, and combustion chamber, confirming proper flame pattern and operational status. Verified electrical connections, wiring integrity, and low-voltage control circuits secured to vertical piping with appropriate mounting hardware.

Completed furnace replacement with associated water heater installation in basement mechanical room. Reworked drop to 10x24 specifications, removed and reinstalled coil, replaced outdated 1-1/2" gas shut-off valve, and installed new humidifier with 1410 controller and condensate pump. All connections verified operational with proper ductwork modifications.

Performed scheduled heating system maintenance and tune-up on residential furnace. Conducted comprehensive temperature diagnostics using digital thermometer, confirming proper system operation at 71.2°F. Inspected and cleaned internal components including blower motor, circuit board, and ventilation connections to ensure optimal performance for the heating season.

Conducted site assessment for replacement of two existing AC units with heat pump systems to create a hybrid heating solution. Exterior inspection revealed two condenser units (cylindrical and box-shaped) positioned alongside concrete walkway near residential building. Interior evaluation of mechanical room showed existing furnace system with connected ductwork, air handler, and associated PVC drainage pipes that will be integrated with new heat pump installation for optimal hybrid operation.

Performed scheduled home plan heating tune-up service. Inspected ventilation components including the heat exchanger fins which appeared in good condition. Replaced severely clogged air filter that showed extensive dust and debris accumulation, which was affecting system efficiency and air quality.

Performed scheduled maintenance on 12-year-old heating system. Inspected interior components including wiring connections, control boards, and PVC ventilation pipes. Noted significant dust accumulation on fan assembly blades requiring thorough cleaning to restore proper airflow and system efficiency.

Successfully completed comprehensive HVAC system replacement including furnace, air conditioning unit, and water heater installation. Modified return drop and overhead collector box to 10x24 specifications and added 1410. Properly positioned outdoor condenser unit on gravel base with appropriate electrical connections and installed new water heater with all necessary plumbing connections in basement utility area.

Performed annual maintenance on 3-year-old furnace under Home Plan Heating Tune Up service. Inspected burner assembly confirming proper flame pattern and color, and conducted combustion analysis using UEi diagnostic meter to verify optimal operating parameters. All electrical connections were checked and secured, and gas valve operation was verified with appropriate hi/lo settings functioning correctly.

Responded to warranty callback for rocking toilet with water leakage. Removed toilet, replaced deteriorated wax ring seal, and reinstalled toilet securely to the flange. Confirmed proper seal and stability after installation with no further leakage observed.

Performed routine maintenance tune-up on 13-year-old furnace with inspection of burner assembly showing proper flame pattern and combustion. Noted presence of large bypass humidifier that requires filter replacement, which was not in service records and customer was unaware of size specifications.

Performed routine maintenance on a 2-year-old furnace under Home Plan Heating Tune Up service. Inspected blower wheel assembly which showed minor dust accumulation on fan blades. Verified proper burner operation with strong, consistent blue flames and examined electrical connections for secure wiring to ensure system reliability.

Successfully completed installation of new steam gas boiler system with integrated backflow preventer, automatic water feeder, and thermostat. Utilized existing 2.5" black pipe infrastructure and main steam vent while ensuring proper connection to the building's plumbing and ventilation systems. System was thoroughly tested and is now operational with all components properly installed according to manufacturer specifications.

Replaced faulty thermocouple on aging furnace system that was preventing proper ignition and causing no-heat condition. Cleaned corroded connection points and verified proper flame sensing after installation. Unit is now operating normally with consistent heat production.