HVAC & Plumbing Services in University Heights

Performed routine maintenance on a 15-year-old Goodman air conditioning system, model SCU10E30A-4. Completed comprehensive tune-up including air filter replacement, visual inspection of outdoor condenser unit, and verification of proper system operation with no issues identified.

Conducted HVAC replacement estimate for a 30-year-old system. Evaluated existing Rheem unit located in basement utility area, noting moisture staining on concrete floor and condensate drainage conditions. Assessed exterior condenser location with overgrown vegetation requiring clearance for proper airflow and service access.

Conducted comprehensive on-site evaluation for complete HVAC system replacement including both furnace and air conditioning units. Assessed existing equipment in basement mechanical room, documented current system configuration including water heater proximity, ductwork layout, and available clearances for new equipment installation. Photographed existing furnace unit with connected supply and return ductwork, insulated piping, and electrical connections to provide accurate specifications for replacement system sizing and compatibility requirements.

Replaced 50-gallon residential water heater in basement utility room. Disconnected existing unit, installed new water heater with proper copper piping connections, ensuring all supply and discharge lines were securely fitted and code-compliant. Verified proper operation of expansion tank and completed system testing to confirm hot water delivery throughout the residence.

Responded to service call for non-functional Arzel zoning system. Upon inspection, discovered damaged ductwork and compromised ceiling penetration at main trunk line junction in basement utility area. Troubleshot system components, identified communication failure between zone control panel and motorized dampers, and assessed structural damage to duct connection points requiring repair to restore proper zone control functionality.

# HVAC Service Call - No Cooling Condition Responded to a no cooling complaint affecting the entire second floor unit. Upon arrival, accessed the air handler cabinet to inspect internal components and verify system operation. Performed visual inspection of the blower motor assembly, control boards, and electrical connections. Checked refrigerant pressures using manifold gauges to assess system charge levels and identify potential issues with the cooling cycle. Examined all visible electrical components including transformers, relays, and wiring connections for proper operation and signs of failure. Inspected copper refrigerant lines at the air handler for leaks, damage, or restrictions. Verified proper condensate drainage through PVC piping system. Evaluated overall system condition and documented findings with photographic evidence of internal components and equipment identification showing second floor designation marked on the Clima 50 unit. System assessed and appropriate correc

Responded to service call for water heater making hissing sound and actively leaking. Upon arrival, inspected AO Smith tanked water heater in basement utility area of ninety-year-old residential property. Assessed unit condition, copper supply piping, expansion tank, and associated valves and fittings. Documented existing installation with photographs showing water heater configuration, plumbing connections, and surrounding utility infrastructure including PVC drainage and metal piping penetrations through foundation walls. Identified source of hissing and water leak, evaluated overall system integrity and functionality.

Completed annual cooling maintenance and tune-up on a 9-year-old air conditioning system. Performed comprehensive system inspection, checked refrigerant pressures and temperatures using digital manifold gauges, cleaned condenser coil fins, and verified proper system operation. All components found to be functioning within manufacturer specifications with no deficiencies noted.

Responded to no-cooling call on 15+ year old Rheem air conditioning unit (Model: RCBA-48B20G21). Found tripped circuit breaker at electrical panel, reset breaker and restored power to system. Verified unit operation and confirmed cooling cycle resumed normally with no further issues observed.

Performed routine maintenance inspection on 3-year-old residential air conditioning system. Verified system operation and cooling performance, documented equipment condition with photos showing furnace unit and ductwork in basement utility area. Customer renewed maintenance plan membership during the service visit.

Completed installation of new kitchen sink and faucet assembly, including undermount stainless steel sink basin with chrome pull-down spray faucet and integrated soap dispenser. Installed Contractor-brand garbage disposal unit with proper mounting hardware and electrical connections. Connected all drain lines using white PVC piping and established proper waste line configuration from disposal to existing drainage system. Verified all water supply connections to hot and cold lines, tested faucet operation and spray head functionality, and confirmed garbage disposal operates without leaks or unusual noise. All components secured and tested successfully.

Performed comprehensive spring preventative maintenance on 2-year-old residential air conditioning system. Conducted complete system evaluation using digital manifold gauge set to measure refrigerant pressures and temperatures across the system. Recorded superheat and subcooling calculations to verify proper refrigerant charge levels. All readings indicated optimal system performance with no refrigerant loss or leaks detected. Inspected outdoor condenser unit positioned in side yard location. Examined condenser coil fins for damage, debris, and airflow restrictions. Verified proper fan motor operation and blade condition. Checked electrical connections at disconnect panel and unit terminals for tightness and signs of overheating. Measured voltage and amperage draw on compressor and fan motor, confirming values within manufacturer specifications. Connected refrigerant manifold gauges to service ports and monitored system operating pressures under ambient conditions. High-side and low-

Responded to service call for 30-year-old Honeywell thermostat experiencing operational issues. Replaced thermostat battery and performed calibration adjustment to restore proper temperature control and system cycling. Verified furnace and HVAC system responding correctly to thermostat commands upon completion.

Completed routine annual air conditioning tune-up on a 2-year-old cooling system with no reported issues. Performed comprehensive maintenance including inspection of outdoor condenser unit, verification of electrical connections and disconnect switches, and standard preventive care procedures. System operating within normal parameters with all components functioning properly.

Provided estimate for relocating existing gas line to accommodate stove repositioning. Assessed current gas supply valve location and determined routing requirements for safe installation. Documented existing conditions including wall-mounted shut-off valve and floor layout to plan proper gas line extension and connection points.

Completed scheduled cooling and heating maintenance on residential HVAC system. Utilized digital manifold gauge to verify refrigerant pressures and temperatures, recording superheat of 6.4°F and subcooling of 7.5°F with system pressures at 103.4 psi and 71.53 psi, indicating proper refrigerant charge and system operation. Performed standard maintenance procedures on both air conditioning condenser unit and furnace to ensure optimal performance for the upcoming season.

Completed routine maintenance and tune-up on 8-year-old boiler system. Performed comprehensive inspection of unit, burner assembly, heat exchanger, and all associated components. System tested and confirmed operating within normal parameters with no issues identified.

Removed and replaced existing water heating system with new Navien tankless water heater featuring integrated recirculation pump and internal buffer tank. Installed new S5 2.1 gallon expansion tank in conjunction with tankless unit to accommodate thermal expansion in closed plumbing system. Configured copper supply lines, PVC venting system, and electrical connections per manufacturer specifications. Unit mounted to wall in basement utility area with proper clearances maintained for service access and ventilation requirements.

Completed annual cooling maintenance and AC tune-up on 3-year-old Heil system. Performed comprehensive inspection of blower wheel assembly, verified proper operation of all mechanical components, and documented equipment condition with photographic records showing normal wear patterns consistent with system age.

Responded to service call for 30+ year old air conditioning condenser unit that would not turn on. Performed diagnostic assessment of outdoor condenser unit and indoor furnace system, documented existing equipment condition showing significant age-related wear and corrosion on condenser top grille. Provided comprehensive estimate for complete HVAC system replacement due to equipment age exceeding serviceable lifespan and non-operational status of cooling system.