HVAC & Plumbing Services in Pepper Pike

Performed comprehensive AC tune-up on 10-year-old system operating normally. Utilized Fieldpiece SMAN manifold gauge to verify refrigerant pressures and system temperatures, confirming proper charge levels and operational parameters across all readings. All measurements indicated system performing within manufacturer specifications with no deficiencies noted.

Completed full air conditioning system replacement including evaporator coil installation. Relocated existing Aprilaire humidifier to accommodate new equipment configuration and ensure proper clearances for the updated HVAC system. All refrigerant lines, condensate drainage, and ductwork connections were properly installed and secured to manufacturer specifications, with system tested and verified operational upon completion.

Responded to a bathtub drainage issue in a 44-year-old residential property where standing water was not evacuating properly from the fixture. Upon arrival, confirmed that only the bathtub was affected while other plumbing fixtures in the bathroom operated normally. Inspected the chrome trip lever overflow assembly and drain cover, noting standing water accumulation in the basin. Removed the overflow plate and extracted the trip lever drain stopper mechanism, which showed signs of hair and soap buildup causing the obstruction. Cleared the accumulated debris from the stopper assembly and cleaned the linkage components. Tested the drain flow and confirmed proper water evacuation. Reassembled the overflow plate and trip lever mechanism, ensuring proper operation of the stopper function. Verified complete drainage with no standing water remaining in the tub. System restored to normal operation.

Performed routine AC tune-up on outdoor condensing unit at customer's request through real estate agent referral. Completed standard maintenance procedures including system inspection, electrical connections check at breaker panel, and verification of proper operation. All equipment found in satisfactory working condition with no issues identified.

Completed comprehensive maintenance service on 13-year-old residential cooling system located on exterior concrete pad. Performed standard MVP Cool maintenance protocol including system inspection, cleaning, and performance verification. Unit is approaching recommended replacement age and customer has been advised of renewal timeline.

Completed full HVAC system installation including a new 80% efficiency gas furnace, 3-ton 14 SEER air conditioning system, and Ecobee thermostat. Relocated the outdoor condensing unit to a new concrete pad position on the driveway, requiring refrigerant line routing through the crawlspace. Installed new ductwork connections, electrical conduit, and line set to accommodate the relocated equipment. System was charged, pressure tested with manifold gauges, and commissioned to manufacturer specifications for optimal performance.

Completed comprehensive Home Plan Cooling Tune Up on residential air conditioning system. Performed full preventive maintenance inspection on outdoor condenser unit and indoor air handler, verified all manufacturer specifications and equipment labels, inspected refrigerant lines and insulation integrity, and confirmed proper drainage system operation. All components found operating within normal parameters with no deficiencies noted.

Responded to service call for three-month-old air conditioning unit not cooling properly. Upon arrival, performed diagnostic temperature readings at outdoor condenser unit using digital thermometer, measuring 94.5°F at the coil assembly. Inspected condenser coils, electrical connections, and capacitor components for proper operation. Documented equipment condition with photos showing temperature measurements and unit components. System evaluated and necessary repairs completed to restore proper cooling function.

Responded to service call for non-functional air conditioning system affecting entire residence. Upon arrival, evaluated 40-year-old outdoor AC unit that had reached end of serviceable life. Conducted comprehensive system assessment including inspection of existing furnace, ductwork, and associated HVAC components in mechanical room. Documented current equipment configuration including furnace unit with connected humidifier, metallic ductwork with visible age-related wear and dust accumulation, and existing copper refrigerant lines. Photographed installation showing gray metal heating equipment, black insulated refrigerant lines with flexible connections, brass valve fittings, and silver metallic duct system. Prepared detailed estimate for complete air conditioning system replacement given the advanced age of equipment and failure to operate, recommending modern energy-efficient replacement unit to restore cooling functionality to the home.

Responded to no cooling call affecting entire residence. Upon arrival, found 40-year-old outdoor air conditioning condenser unit in severely deteriorated condition. Performed visual inspection of exterior unit, noting extensive age-related wear, discoloration, and debris accumulation on condenser coils and housing. Documented unit condition with photographs showing significant staining on louvers and compromised system components. Given the unit's age well beyond typical equipment lifespan of 15-20 years, advised customer that repair would not be cost-effective and recommended full system replacement. Unit has exceeded manufacturer's intended service life by more than two decades and shows multiple signs of end-of-life failure.

Responded to service call for no airflow issue in residential ventilation system. Upon inspection, found disconnected flexible duct section in crawl space with visible moisture damage and staining on metal ductwork. Reconnected and secured duct sections at coupling point, restoring proper airflow to affected area. System tested and verified operational upon completion.

Responded to service call for 2-year-old air conditioning system reported as not working properly. Upon inspection, discovered extensive frost and ice buildup on evaporator coil and blower assembly, indicating restricted airflow or low refrigerant charge. Performed diagnostic testing using refrigerant manifold gauges to measure system pressures and temperatures. Low-side pressure reading of 0.045 psig and high-side pressure of 274.7 psig confirmed severely restricted airflow due to dirty or blocked evaporator coil causing system to freeze. Shut down system to allow complete defrost of evaporator coil. Inspected air filter and found it heavily soiled, restricting airflow to the system. Replaced air filter with proper size filter. Once coil fully defrosted, verified blower motor operation and checked fan speed settings. Cleaned evaporator coil thoroughly to remove dust and debris accumulation. After coil cleaning and filter replacement, restarted system and monitored operation. Recheck

Conducted on-site consultation for tankless water heater replacement to evaluate existing 75-gallon conventional water heater system. Assessed current installation including gas supply line configuration, venting requirements, electrical connections, and available space for tankless unit conversion. Documented existing Honeywell gas control valve, flexible gas connector, and current plumbing infrastructure including copper water lines and PVC drainage system to determine compatibility and necessary modifications for tankless installation.

Conducted follow-up inspection and documentation of existing electrical service panel in preparation for HVAC system replacement. Photographed current electrical configuration, including main service disconnect, circuit breaker layout, and existing air conditioner circuit identification to assess compatibility and electrical capacity requirements for new equipment installation.

Completed preventive maintenance on two 12-year-old air conditioning systems for maintenance value plan member. Performed comprehensive inspection, cleaning, and testing of both units to ensure optimal cooling performance and system efficiency for the upcoming season.

Replaced failed condenser fan motor, fan blade, and run capacitor on outdoor air conditioning unit. System was cycled and tested to verify proper operation of all components. Customer was advised that due to the age and overall condition of the equipment, replacement of the entire air conditioning system should be considered in the near future.

Completed comprehensive AC tune-up on two systems: one indoor unit located in basement and one outdoor unit in backyard, both approximately 3-4 years old. Performed thorough inspection of blower wheel assembly, verified proper operation and cleanliness of centrifugal fan components, and conducted refrigerant system diagnostics using digital manifold gauges to confirm optimal pressure and temperature readings across both systems.

Performed comprehensive tune-up and maintenance inspection on dual cooling system consisting of outdoor central air conditioning condenser unit and interior ductless mini-split system. Completed standard preventive maintenance procedures including visual inspection of both units, verification of proper operation, and system performance evaluation with no issues identified during service call.

Recovered all R-410A refrigerant from the condenser unit and replaced four outdoor refrigerant lineset flare fittings. Recharged the system to manufacturer specifications with additional R-410A refrigerant as needed to achieve proper factory charge levels. Performed general AC system checkup to verify proper operation following repair.

Completed routine AC tune-up maintenance on three residential air conditioning systems located in attic and crawl space installations. Performed standard diagnostics including refrigerant pressure and temperature measurements using manifold gauges, verifying system operating parameters were within manufacturer specifications. All three units found operating properly with no deficiencies noted; customer advised that air filters need replacement on two systems previously installed by company.