HVAC & Plumbing Services in Lakewood, OH

Responded to service call for 15-year-old Mitsubishi multi-zone mini-split system with multiple indoor units not cooling properly. Upon arrival, performed comprehensive system diagnostic including refrigerant pressure testing, electrical component inspection, and airflow assessment of both outdoor condensing unit and indoor air handlers. Noted significant leaf debris accumulation around outdoor unit affecting airflow and heat exchange efficiency. Cleared all debris from condensing unit perimeter and coil surfaces, inspected refrigerant lines for leaks, and tested system operation. Checked refrigerant charge levels and confirmed system had lost refrigerant since previous service. Located and repaired refrigerant leak, evacuated system, and recharged to manufacturer specifications. Verified proper operation of all indoor zones, confirmed adequate cooling output, and tested thermostat functionality. System restored to full operational capacity with all units now providing proper cooling p

Conducted complimentary water heater estimate in residential basement for potential replacement of existing unit. Assessed current dual water heater configuration and discussed sizing options with homeowner, including possibility of upgrading to 80-gallon capacity tank to meet household hot water demand requirements. Documented existing plumbing connections, copper supply lines, shut-off valves, and current installation layout for preparation of replacement proposal.

Conducted comprehensive site assessment for commercial steam boiler replacement in industrial mechanical room with exposed brick walls and concrete flooring showing moisture damage. Evaluated existing equipment condition, documented deteriorated cylindrical boiler component with visible rust and corrosion, assessed piping infrastructure and structural supports, and photographed installation environment including access stairwell. Provided detailed estimate for complete boiler system replacement.

Completed routine maintenance and tune-up on 12-year-old Armstrong Air conditioning system. Performed comprehensive system inspection, measured refrigerant charge levels using calibrated digital scale, verified electrical connections and control board operation with all indicator LEDs functioning properly. No deficiencies noted; system operating within manufacturer specifications.

Responded to service call for radiator removal. Successfully disconnected and removed eight cast iron radiators from various locations throughout the residence, including units from bedroom and bathroom areas, to allow customer to have them professionally sandblasted for restoration. All radiator connections were properly capped and secured to maintain system integrity during the interim period. Documented existing radiator locations and configurations with photographs for accurate reinstallation reference. Provided quote for future reinstallation of all eight radiators upon completion of sandblasting work.

Conducted on-site assessment for mini split air conditioning installation on second floor of residence with hot water heat. Evaluated attic access and structural conditions, documenting exposed ceiling joists, existing insulation, and electrical routing to determine optimal placement for indoor and outdoor units compatible with customer's preference for non-automated controls.

Conducted estimate for potential AC replacement in residential property with existing furnace and water heater system located in basement mechanical room. Evaluated current HVAC system capacity and determined unit may be undersized for the home's cooling requirements, including converted attic office space with multiple electronic devices generating additional heat load. Documented existing equipment configuration and ductwork layout with photographs for replacement proposal preparation.

Performed comprehensive tune-up service on a 10-year-old Rheem outdoor condensing unit (Model RA1330AJ1RA, manufactured 05/2015) that had never received prior maintenance and was producing unusual operational noise. Conducted full system diagnostics using digital multimeter to verify electrical performance, including voltage readings, amperage draw, and contactor operation. Inspected condenser coil condition, fan motor operation, and compressor functionality. Unit showed signs of extended outdoor exposure with dirt accumulation and minor surface corrosion on cabinet panels. Verified proper refrigerant pressures and system cycling. Cleaned condenser coil of debris and contamination to restore optimal airflow and heat transfer efficiency. Checked all electrical connections at single pole contactors per manufacturer specifications. Lubricated fan motor bearings and tightened mounting hardware to eliminate noise source. System restored to proper operating condition with improved performanc

Completed comprehensive assessment of existing Unico small-duct high-velocity HVAC system for replacement estimate. Evaluated current air handler unit located in attic mechanical space, documenting equipment condition, operational status, existing ductwork configuration including reflective flex duct distribution, and refrigerant line routing. Inspected ceiling-mounted supply registers noting age-related discoloration and assessed overall system accessibility for future replacement work. Photographed equipment specifications and installation environment to provide accurate replacement proposal.

Conducted on-site assessment of residential property to provide heating options for second floor. Evaluated attic space and existing electrical infrastructure to determine feasibility of extending ductwork from current HVAC system versus installing ductless mini-split units. Documented attic framing, existing ductwork routing, insulation conditions, and available electrical panel capacity to develop comprehensive estimate for customer consideration.

Conducted on-site assessment for mini split installation on third floor of residential property. Evaluated exterior wall mounting location, verified electrical service capacity at existing meter bank, and inspected interior electrical panel to confirm adequate breaker availability and proper grounding for new system installation.

Conducted on-site assessment for ductless mini-split air conditioning installation to supplement existing boiler heating system. Evaluated room layout, electrical requirements, and optimal placement for indoor and outdoor units to ensure efficient cooling coverage for the space.

Inspected and replaced severely corroded valve and supply line in 100-year-old residence. Removed accumulated debris from floor register, cleaned surrounding tile area, and installed new braided stainless steel supply line with quarter-turn valve. System tested with positive results - no leaks observed under normal operating pressure.

Performed site assessment for potential tankless water heater installation in basement utility area. Evaluated existing plumbing configuration, ventilation requirements, and available utility connections. Due to scheduling confusion, waived service call fee and provided customer with installation options and recommendations.

Responded to natural leak in main drain line of century-old home. Inspected exposed piping in ceiling area, including copper and darker drain lines. Repaired leaking section of main drain pipe to restore proper drainage function.

Responded to service call for newly installed boiler experiencing recurring low water float issues. Upon inspection, identified oxidation on copper pipes and examined the control wiring system. Performed necessary adjustments to the float mechanism and verified proper electrical connections to resolve the persistent low water reading problem.

Performed scheduled heating tune-up on 4-year-old MVP system, which had been rescheduled twice. Inspected heat exchanger showing signs of corrosion and moisture accumulation in collection pan. Verified proper burner operation with strong blue flames at base transitioning to orange tips, indicating normal combustion.

Upon arrival, diagnosed a no-heat condition in the existing boiler system. Performed comprehensive inspection of the unit, including circulation pump, PVC venting system, and associated copper piping/valves. Provided customer with detailed estimate for both repair options and complete system replacement.

Completed vent replacement in collaboration with Joseph (3 hours). Discovered corroded pipe section containing sediment buildup, which was removed during service. Installed new venting components and verified proper connection to existing plumbing system. All work completed as scheduled.

Responded to service call for leaking dishwasher shut-off valve. Upon inspection, discovered mineral buildup around valve joint, indicating ongoing seepage. Replaced faulty valve assembly to resolve leak, eliminating need for temporary bucket collection solution.