HVAC Services in Cleveland, OH

Performed full furnace replacement after identifying non-repairable belt failure. Removed existing aged unit and installed new Rheem furnace system in basement mechanical room. Connected new unit to existing ductwork and verified proper installation and operation.

Performed scheduled furnace maintenance service. Conducted combustion analysis using Testo 310 analyzer, with readings showing O₂ at 13.1% and CO at 29 ppm, indicating proper combustion within acceptable safety parameters.

Responded to service call for hot water tank leak. Performed comprehensive inspection of plumbing system in utility area, focusing on copper supply lines, brass fittings, and flexible braided hoses. Identified and repaired leak source, ensuring proper connections and functionality of the hot water system.

Completed installation of new boiler in renovation property, replacing all 18 radiator vents throughout the home. Replaced defective auto feeder on boiler (potentially warranty-eligible) and remediated significant banging issues by replacing all underground wet return piping and converting approximately 20 feet of copper supply line to properly pitched 2" black pipe.

Responded to no-heat call for a 2-year-old furnace. Inspected ductwork and air handler unit in basement, identified issue with STDGR component (HOP 8X60). Restored heating functionality by performing necessary repairs to the affected components.

Performed heating tune-up on 3-year-old Rheem Performance water heater. Inspected and cleaned blower wheel assembly to ensure optimal operation. System functioning properly with all connections secure and ventilation in good condition.

Performed comprehensive tune-up on residential heating system of indeterminate age. Inspected blower wheel assembly and heat exchanger, noting normal dust accumulation but proper operation of burner ports with consistent blue flame pattern. System functioning within normal parameters after service.

Successfully replaced customer's garbage disposal unit with new model, properly connecting all PVC drain pipes and ensuring secure mounting to sink with appropriate seals. Tested unit for functionality and proper drainage with no leaks observed.

Performed comprehensive furnace tune-up service, conducting combustion analysis with readings of 7.0% O2, 18 ppm CO, and 7.9% CO2 at stack temperature of 92.6°F, indicating unit is operating within acceptable parameters. Verified thermostat functionality, currently set at 66°F with ambient temperature reading 76°F.

Inspected 13-year-old steam boiler system to provide estimate for pipe replacement. Documented extensive corrosion and mineral deposits on existing copper piping, particularly at valve junctions, with visible water damage to surrounding areas. Noted previous partial replacement with PVC piping, but recommended complete replacement of remaining deteriorated copper sections to prevent potential failure.

Conducted scheduled maintenance on steam boiler system per Home Plan agreement. Performed comprehensive diagnostic testing using digital analyzer, confirming proper operating temperatures with readings at 104.7°F. All temperature differentials were within manufacturer specifications across multiple measurement points.

Performed comprehensive service certification on six gas furnaces at commercial property. Inspected Concord unit and associated ductwork in utility room, noting proper installation of ventilation components and confirming operational status. Visual inspection revealed no immediate safety concerns with the equipment or surrounding mechanical systems.

Diagnosed no heat condition in residential furnace system. Replaced failed control board and inducer motor assembly to restore proper operation. Verified proper ignition sequence, flame detection, and heating function after repair with successful test run showing normal burner operation.

Responded to service call for leaky faucet in century-old residential property. Upon inspection, identified mineral buildup in the aerator screen and wear on valve components causing the leak. Disassembled fixture, cleaned mineral deposits, replaced worn gaskets and reassembled, confirming proper operation with no further leakage.

Responded to service call for 20-year-old furnace not operating properly. Inspection revealed dusty but functional burners with proper blue flame pattern. System was tested and confirmed to be operating within normal parameters; no immediate repairs needed at this time.

Conducted plumbing assessment in basement area, examining PVC pipes along wall-ceiling junction for reported crack and moisture issues. Inspection revealed minor discoloration and moisture staining on lower portion of concrete block wall. Documented existing plumbing configuration and potential moisture intrusion points for follow-up repair recommendations.

Diagnosed 8-year-old gas furnace with no heat complaint through inspection of internal components including blower assembly, circuit board, and wiring harnesses. Identified and replaced faulty flame sensor which was causing system lockout, preventing ignition sequence. System now operating properly with normal heating function restored after testing multiple heating cycles to confirm repair.

Performed scheduled maintenance on Bryant outdoor condensing unit and associated furnace system. Inspected unit placement and connections, noting proper installation on gravel base with secure connection pipes to building. System is functioning properly with no issues observed.

Performed routine maintenance on 3-year-old natural gas furnace under MVP Home Plan. Conducted combustion analysis with UEi C161 analyzer, measuring O2 at 12.53%, CO2 at 4.82%, and stack temperature at 87.7°F. Supply temperature reading of 716° was verified with digital probe at ductwork. All parameters within normal operating range for this 1-5 ton system.

Performed Home Plan Heating Tune Up on residential HVAC system. Inspected and replaced pleated air filter which showed moderate dust accumulation. Conducted visual inspection of furnace unit and surrounding ventilation components in basement utility area.