HVAC & Plumbing Services in Chagrin Falls, OH

Performed comprehensive maintenance on 3-year-old air conditioning system including inspection of outdoor condensing unit and verification of system operation. Measured and recorded refrigerant pressures and temperatures using manifold gauge set, confirming R-410A charge levels with superheat at 70°F and subcooling at 46°F within manufacturer specifications. Replaced humidifier water panels as requested and completed all standard preventative maintenance procedures to ensure optimal system performance for upcoming home inspection.

Responded to service call for leaking water softener unit located in meat room. Upon arrival, inspected the system and identified active leak at valve assembly connections. Documented equipment condition showing visible corrosion, mineral deposits, and aging components on brass fittings. Assessed flexible hose connections and clamps for integrity. Photographed rental unit tag information and internal plumbing configuration including corroded valve mechanism, flexible supply lines, and corrugated hoses for service records and potential replacement recommendations.

Completed comprehensive cooling system tune-up on outdoor condensing unit positioned against exterior brick wall. Performed standard preventive maintenance protocol including inspection of condenser coils through perforated side panels, verified fan motor operation and blade integrity behind protective wire guards, checked refrigerant levels, cleaned debris from unit exterior and surrounding area, and confirmed proper airflow through top-mounted fan assembly. Unit found in functional condition with normal weathering consistent with outdoor installation; all components operating within manufacturer specifications upon completion of service.

Completed full HVAC system replacement including outdoor condensing unit and indoor evaporator coil. Existing refrigerant line set was inspected, pressure tested, and reused to minimize installation time and cost. New condenser unit was positioned on existing concrete pad with proper clearances maintained. Indoor evaporator coil was installed above furnace/air handler in basement mechanical room, integrated with existing ductwork system. All refrigerant lines were properly connected and insulated. System was evacuated to manufacturer specifications, charged with appropriate refrigerant type and quantity per equipment requirements. Electrical connections were completed at both indoor and outdoor units with proper disconnect switches verified. Condensate drain system was connected and tested for proper operation. System startup performed with all operating pressures and temperatures verified within normal parameters. Airflow across coil confirmed adequate. Unit cycled through complete co

Completed annual AC tune-up on 3-year-old system that was operating normally. Performed standard preventive maintenance including inspection of blower motor assembly, verified proper operation of fan wheel and motor components, and documented equipment condition with photos. System confirmed to be functioning within normal parameters with no issues identified.

Performed comprehensive air conditioning tune-up on 3-year-old outdoor condensing unit. Conducted full system diagnostics including temperature measurements, inspected refrigerant lines and electrical connections, verified proper operation of all components, and ensured unit is operating within manufacturer specifications for optimal cooling performance.

Conducted on-site assessment of existing HVAC system in basement utility room for equipment replacement estimate. Evaluated current furnace unit, associated ductwork, PVC condensate drainage system, and ventilation components. Documented existing installation configuration including furnace positioning, clearances, and integration with water heater and plumbing infrastructure. Photographed equipment specifications, warning labels, and surrounding mechanical systems to prepare comprehensive replacement proposal.

Completed preventative maintenance tune-up on a 6-7 year old air conditioning system. Performed standard inspection of outdoor condenser unit, verified refrigerant line connections, and tested system operation using digital diagnostic equipment. All components found to be in proper working condition with no issues identified.

Completed comprehensive annual air conditioning tune-up and system inspection on residential cooling system. Performed standard maintenance protocol including refrigerant pressure testing using digital manifold gauge, verified proper system operation, and inspected indoor air handler unit and outdoor condenser coil condition. All components found operating within normal parameters with no issues identified or repairs required at this time.

Replaced leaking filter drier using ProPress connection method to ensure secure, leak-free installation. System was evacuated to proper vacuum levels as confirmed by digital vacuometer readings, then recharged with refrigerant to manufacturer specifications.

Completed preventative maintenance on residential air conditioning system. Performed thorough inspection of outdoor condensing unit and internal electrical components, including capacitor, contactor, and motor connections. Cleaned accumulated dust, debris, and cobwebs from electrical compartment and verified all wire connections were secure. System operational and running within normal parameters upon completion.

Performed on-site evaluation of existing 41-year-old Trane air handler system located in basement utility area. Documented current equipment condition, configuration, and installation specifications through photographic assessment. Prepared comprehensive replacement quote for complete heat pump system upgrade to address aging HVAC equipment that has exceeded its expected service life.

Performed comprehensive evaluation of 7-year-old heat pump system as requested second opinion. Upon inspection, identified significant electrical component deterioration including corroded contactor terminals and aged wiring connections showing oxidation and environmental damage. Documented unit condition with exterior and internal electrical compartment photography, revealing system installed on concrete pad with proper clearances but exhibiting wear consistent with age and exposure. Provided assessment findings and replacement recommendations to customer for consideration.

Completed full HVAC system replacement for a 2-story addition, converting from cooling-only to complete heating and cooling. Installed new Bryant furnace with evaporator coil, outdoor condenser unit, and programmable thermostat. Vented furnace exhaust through crawlspace using PVC piping. Reused existing airflow base and integrated air cleaner beneath furnace for improved indoor air quality. Replaced refrigerant linesets that previously ran under a removed deck, securing new lines to exterior siding and enclosing in line hide for protection and aesthetics. Routed lineset under slider door to maintain proper clearance and appearance. Connected to existing gas supply located near main house boiler system. Installed electrical disconnect and completed all wiring connections to code. System tested and operational, providing both heating and cooling capabilities to the addition with proper airflow distribution through existing ductwork.

Completed recurring heating maintenance on 8-year-old residential gas furnace system. Performed comprehensive inspection of burner assembly, confirming proper operation of three-burner gas manifold with all burners igniting cleanly and flame sensors functioning within specifications. Inspected blower wheel assembly for debris accumulation and balance, verifying unrestricted airflow through squirrel cage fan and proper motor operation. All components photographed and documented showing normal wear patterns consistent with system age and operational history. Unit tested and left in proper working condition.

Completed installation of new tanked water heater in basement utility room. Positioned unit on concrete floor with proper clearances and connected copper supply lines with brass fittings to top of tank. Installed venting ductwork extending to ceiling joists and mounted control panel/thermostat on adjacent concrete block wall for temperature regulation. Collected deposit payment as customer approved hot water tank replacement option.

Completed HVAC replacement estimate for a 24-year-old Carrier air conditioning system, including evaluation of both the indoor air handler unit located in the basement mechanical room and the outdoor Allegiance 10 condenser unit (Model 7A0048B100A1, SEER 10.0, manufactured 05/2002). Documented existing equipment conditions with photographs and confirmed customer contact information for proposal delivery.

Completed comprehensive tune-up service on residential air conditioning and furnace system. Performed diagnostic testing using digital manometer to verify proper airflow and static pressure readings, measuring 75.4 inches water column within the air handler unit. Inspected internal components, electrical connections, and insulation integrity on both heating and cooling equipment to ensure optimal system performance and energy efficiency.

Performed scheduled heating system maintenance on a residential furnace unit per maintenance agreement. Inspected all components including ductwork, electrical connections, and combustion system for proper operation. System is functioning within normal parameters with no issues identified; documentation completed with photo verification of equipment condition.

Performed annual maintenance on an 8-year-old cooling system. Inspected blower wheel assembly which showed moderate dust accumulation on the fan blades and housing. Cleaned blower wheel to restore proper airflow and system efficiency.