HVAC & Plumbing Services in Cleveland Heights, OH

Responded to water leak complaint in downstairs half bath with ceiling damage. Upon investigation, traced leak source to upstairs closet area where carpet showed significant water staining and discoloration. Inspected bathroom vanity plumbing connections, P-trap assembly, and supply lines for potential failure points in the fifty-year-old home's plumbing system.

Completed service return trip to install new water heater with pressure relief valve. System tested and confirmed operational with proper pressure readings via gauge monitoring. Previous water damage and floor staining observed at installation location, indicating prior leakage issues have been resolved with new equipment installation.

Provided free estimate for replacement of existing Lochinvar 40-gallon tall natural gas water heater with regular atmospheric vent. Inspected current installation including copper supply lines, gas connections, pressure relief valve configuration, and galvanized vent piping to determine scope of replacement work and ensure proper sizing for residential hot water demands.

Completed comprehensive heating maintenance on a 5-6 year old Bryant electric furnace system. Performed full system inspection including burner assembly operation verification, confirmed proper ignition sequence with burners firing cleanly with blue flames, checked all electrical connections and safety controls, inspected heat exchanger, verified proper venting through PVC intake and exhaust pipes, and tested blower motor operation. All components found operating within normal parameters and system returned to service in good working condition.

Conducted on-site assessment of existing two-piece toilet installation to provide replacement and installation quotation. Evaluated current bathroom configuration, including white porcelain toilet with chrome flush mechanism, plumbing access points, and floor conditions with hexagonal mosaic tile. Documented existing fixture specifications and took measurements to determine appropriate replacement options and labor requirements for complete toilet removal and new unit installation.

Responded to service call for 4-year-old mini split system experiencing water leakage. Accessed internal components by removing front cover of wall-mounted indoor unit to inspect blower assembly, drain system, and refrigerant line connections. Performed diagnostic evaluation of evaporator coil, condensate drainage pathway, and blower fan operation to identify source of leak and ensure proper system function.

Completed full HVAC system replacement in basement utility area, including removal of existing equipment and installation of new furnace, evaporator coil, air conditioning unit, and thermostat. Installed gray metal furnace on concrete floor with proper clearances and connected large-diameter metal ductwork extending to upper air handler components, securing all connections with metal bands per manufacturer specifications. Mounted evaporator coil in appropriate position within duct system to ensure optimal airflow and refrigerant distribution. Connected new air conditioning condenser unit to system with proper refrigerant lines and electrical connections. Installed new programmable thermostat and verified communication with HVAC equipment. Addressed airflow concerns for upstairs zone by evaluating existing vent configuration and installing additional return vent on back side of system to improve air circulation and balance throughout home. Performed comprehensive system startup proced

Completed annual maintenance and tune-up on 9-year-old Lennox furnace system. Performed comprehensive inspection of all mechanical components, verified proper operation of burner assembly, and conducted combustion analysis. Flue gas readings confirmed optimal efficiency with oxygen level at 6.3%, carbon dioxide at 8.2%, carbon monoxide at 0 ppm, and stack temperature at 375.4°F. All measurements within manufacturer specifications. Inspected heat exchanger, blower assembly, and ductwork connections. Verified proper clearances to combustible materials and confirmed all safety labels intact. System operating properly with no issues found. Unit is in good working condition.

Performed annual maintenance on 7-year-old boiler system operating without reported issues. Inspected gas burner assembly with active combustion showing proper blue flame pattern across all burner tubes. Observed significant soot and debris accumulation on heat exchanger surfaces above burner assembly, indicating normal aging but requiring monitoring. Examined aged copper piping system displaying heavy oxidation and green patina throughout vertical and horizontal runs. Verified all mechanical connections, gauges, and system components for proper operation. Documented equipment condition through photography for maintenance records. System operating within normal parameters upon completion of tune-up procedures.

Replaced laundry tub faucet in basement utility area. Installation completed in two hours with proper mounting to existing plumbing connections and verification of water flow and drainage functionality.

Responded to service call for water accumulation around boiler system. Upon inspection, identified water heater in basement utility area with deteriorated plumbing connections and visible moisture issues. Examined copper piping, galvanized vent stack, and associated mechanical components for signs of leakage. Documented conditions including aged infrastructure, corroded piping with dark deterioration along vertical runs, and wall staining indicative of previous water exposure. Assessed water meter connections, pressure relief valve, and all visible joints for active leaks or seepage points to determine source of reported water accumulation.

Responded to service call for furnace control panel evaluation. Upon arrival, performed diagnostic inspection of gas furnace system in basement utility area. Verified burner assembly operation with all igniters firing properly and producing proper blue flame pattern. Inspected electrical control wiring including ignition system connections, safety circuits, and thermostat wiring. Documented current system condition with photographs showing burner operation and overall unit configuration. Examined control board and associated electrical components for signs of failure or malfunction. Assessed control panel replacement requirements and prepared quotation for new control board installation. Unit operational at time of departure pending customer approval for control panel replacement.

Performed routine maintenance service on a 2-year-old residential boiler system located in basement mechanical room. Conducted comprehensive inspection of boiler unit, control systems, and associated components. Verified proper operation of electrical controls, inspected pressure gauge readings, examined copper piping connections for leaks or corrosion, and checked all safety systems. All components found to be functioning within normal parameters with no issues identified requiring repair.

Completed comprehensive tune-up on a 10-year-old gas furnace located in basement. Performed full system inspection including burner assembly operation verification, heat exchanger examination, and combustion analysis. All burners igniting properly with appropriate flame characteristics showing blue/purple coloration indicating efficient combustion. Heat exchanger inspected and found to be in serviceable condition with no visible cracks or deterioration. System operational and ready for heating season.

Responded to service call for Rheem tankless water heater approximately six years old. Performed comprehensive diagnostic inspection of unit with cover removed to assess internal components including heat exchanger, blower assembly, and control board. Inspected all connections including gas line, water supply lines, and PVC venting system for proper installation and function. Documented unit condition with photos showing heat exchanger coils, fan assembly, digital display panel, and associated plumbing connections. New homeowners required assessment of existing system to determine operational status and identify any maintenance needs.

Performed comprehensive preventative maintenance on a ten-year-old residential boiler system located in the basement. Conducted complete tune-up service including inspection of all mechanical components, burner assembly, heat exchanger, flue piping, and associated plumbing connections. Verified proper operation of all safety controls, tested combustion efficiency, and confirmed system is functioning within manufacturer specifications with no issues identified.

Responded to follow-up service call for non-operational air conditioning system after previous utility power issue. Upon arrival, discovered severely corroded electrical disconnect box with extensive rust damage and deterioration to mounting components and wiring connections. Found substantial debris accumulation including nest material and organic matter around electrical components, creating potential safety hazard and contributing to equipment failure. Replaced damaged disconnect box and corroded electrical components, cleaned all debris from area, verified proper voltage supply at 240V, and restored power to outdoor condensing unit. System tested and confirmed operational with normal amperage draw and proper cooling cycle.

Responded to service call regarding hot water tank issue in basement location. Upon arrival, conducted thorough inspection of tanked water heater unit, including examination of copper supply lines, shut-off valves, and overall unit condition. Assessed water heater for proper operation, checked for visible leaks or moisture around base and connections, and verified all safety labels and manufacturer specifications were intact. Documented unit condition with photographs for service records.

Relocated shower faucet controls from side wall mounting to standard configuration, consolidating multiple valve handles into a single set of controls. Reconfigured plumbing supply lines behind tile wall, installed new valve assembly, and ensured proper water flow and temperature control functionality upon completion.

Completed preventive maintenance on three furnace systems. Performed comprehensive inspections including blower wheel examination, system diagnostics with digital manifold gauge, and operational testing. All units found to be operating within manufacturer specifications with blower assemblies clean and functional.