HVAC & Plumbing Services in Cleveland Heights, OH

Conducted comprehensive evaluation of existing HVAC system including Armstrong Ultra V furnace unit and associated ductwork infrastructure in basement mechanical room. Documented current equipment condition, noting age-related wear on flexible ductwork with dust accumulation, and assessed overall system configuration including water heater and expansion tank setup. Provided detailed replacement estimate for complete system upgrade to address equipment lifecycle and efficiency concerns.

Responded to no-heat call where tenants were unable to operate boiler system with landlord unavailable. Provided instruction on proper boiler startup procedures and verified system operation. Performed combustion analysis confirming acceptable readings with oxygen at 7.8%, CO2 at 7.5%, and stack temperature at 314.4°F, indicating efficient burner performance. Inspected heat exchanger tubes and internal components, finding system in proper working order with no safety concerns.

Responded to callback for non-functioning thermostat on recently installed boiler system. Inspected Emerson thermostat installation and verified proper wiring connections between thermostat and boiler control board. Tested thermostat functionality, confirmed display operation, and ensured proper communication with heating system. System now operating correctly with thermostat successfully controlling boiler operation.

Performed comprehensive assessment of 50+ year old boiler system for replacement estimate. Customer previously advised by another contractor that unit required replacement but was not provided diagnostic information. Documented existing system configuration including aged furnace/air handler unit, associated ductwork, gas piping, water connections, and pressure control components in basement mechanical room. Photographed current equipment installation to provide accurate replacement specifications when customer is ready to proceed with system upgrade.

Completed full bathroom plumbing renovation including removal of existing cast-iron bathtub with demolition of surrounding drywall and wood framing extending to ceiling. Opened kitchen ceiling section to access and remove obsolete galvanized water supply lines, cast iron drain fittings, lavatory drain, and toilet bend. Replaced all piping with code-compliant PVC drainage system. Installed new alcove-style white bathtub in prepared opening with proper anchoring and connections to updated plumbing infrastructure.

Completed comprehensive heating system maintenance including inspection of blower assembly and air-moving components. Verified proper operation of blower wheel, checked mounting hardware and central hub assembly for secure installation, and documented equipment condition with photographic records. All components found to be functioning within normal parameters with minor wear consistent with regular use.

Performed comprehensive inspection on 10-year-old residential boiler system. Examined expansion tank, circulator pumps, pressure relief valves, and all associated copper piping and brass fittings for proper operation and potential wear. Verified system pressure, checked all valve operations, inspected circulator pump function, and confirmed proper connections throughout the heating distribution network. All components found to be operating within normal parameters with no immediate repairs required at this time.

Completed comprehensive furnace tune-up and replaced failed condensate pump. Performed combustion analysis using digital analyzer, confirming optimal efficiency with CO2 levels at 4.3% and excess air readings within manufacturer specifications. System now operating safely with proper condensate drainage restored.

Conducted comprehensive evaluation of 25-year-old HVAC system experiencing circuit breaker tripping issues. Inspected furnace, evaporator coil unit manufactured by International Comfort Products, and associated electrical components in basement mechanical room. Documented existing equipment condition and electrical concerns, provided detailed replacement estimate for aging system showing signs of potential electrical failure.

Responded to preventative plumbing maintenance call following resolution of slow drain issue. Performed comprehensive inspection of under-sink plumbing assembly, identifying brown discoloration and potential corrosion on upper pipe connection points. Discussed preventative maintenance recommendations with property occupant, including regular drain cleaning protocols and monitoring of visible pipe degradation. Documented plumbing configuration with photographic evidence showing flexible supply lines, corrugated drain pipe, and water meter installation for future reference.

Completed annual tune-up on 11-year-old residential hot water boiler. Performed combustion analysis using digital analyzer, recording flue gas temperatures and CO2 levels to verify efficient operation. Inspected burner assembly, confirmed proper flame characteristics with blue primary flames and minimal yellow tipping, indicating optimal air-fuel mixture. All safety controls tested and operating within manufacturer specifications.

Performed comprehensive preseason assessment and tune-up on two 23-year-old residential furnace systems. Completed full inspection of heat exchangers, burner assemblies, and ductwork connections, documenting condition with photographic evidence showing coil fins and insulated ductwork with associated electrical connections. All systems evaluated for operational integrity and replacement recommendations, with no active malfunctions reported at time of service.

Conducted estimate for replacement of 15-year-old residential furnace unit found to be in poor condition. Assessed existing gray metal furnace system with associated PVC venting and condensate drainage lines, along with connected ductwork and humidification components in basement mechanical room. Documented equipment condition through photos and provided replacement recommendations to customer.

Performed comprehensive heating system tune-up on basement furnace unit. System was operating properly upon arrival with no reported issues or symptoms. Completed full preventive maintenance inspection including examination of heat exchanger panels, burner assembly, and copper gas line connections. All components were found to be in satisfactory working condition and system passed operational testing.

Responded to service call for broken toilet handle replacement. Upon arrival, conducted comprehensive plumbing assessment of property as requested. Documented extensive water damage and deterioration to basement ceiling area, including significant rust staining on white PVC and copper piping, compromised ceiling material with exposed structural beams, and evidence of long-term moisture intrusion affecting multiple pipe runs and cleanout fittings. Photographed conditions for record and recommended further evaluation of water damage source and structural concerns.

Completed comprehensive maintenance inspection on a 7-year-old gas furnace system. Performed visual and operational assessment of all internal components including gas valve assembly, ignition system, safety controls, and electrical connections. All wiring harnesses, sensors, and control mechanisms were inspected and found to be functioning within normal parameters with no immediate service needs identified.

Completed full packaged HVAC system replacement including new air handler unit and digital thermostat. Verified proper installation with static pressure readings of 15.0 using calibrated UEi EM152 manometer, confirmed all ductwork connections are secure, and ensured unit is operating within manufacturer specifications with all safety labels and energy guide documentation properly affixed.

Completed kitchen sink drain replacement at residential property. Two-person crew successfully removed existing deteriorated drain assembly and installed new PVC drainage system. Work included addressing significant floor deterioration and water accumulation issues discovered at the base of the existing vertical drain pipe in the basement utility area. Cleared debris and standing water from affected concrete floor section, ensuring proper drainage flow and structural integrity of new installation. All components installed to code specifications with secure connections and proper sealing to prevent future moisture infiltration.

Completed annual maintenance and tune-up on 8-year-old boiler system per membership agreement. Performed comprehensive inspection of heat exchanger, burner assembly, gas valve components, and all electrical connections. Conducted combustion analysis testing using diagnostic meter to verify proper gas pressure, temperature readings, and system efficiency. Inspected finned heat exchanger plates for signs of deterioration or carbon buildup, confirmed condensate drain pan and PVC drainage lines were clear and functioning properly. All components found to be operating within manufacturer specifications with no immediate safety concerns or repair needs identified at this time.

Responded to water leak complaint in downstairs half bath with ceiling damage. Upon investigation, traced leak source to upstairs closet area where carpet showed significant water staining and discoloration. Inspected bathroom vanity plumbing connections, P-trap assembly, and supply lines for potential failure points in the fifty-year-old home's plumbing system.