HVAC & Plumbing Services in Cleveland Heights, OH

Completed fixture swap-out in second-floor bathroom, replacing existing plumbing components. Work included installation and connection of pedestal sink with chrome faucet and associated supply lines and shut-off valves, ensuring proper water flow and leak-free operation.

Completed comprehensive fall heating tune-up on 10-year-old furnace located in basement. Performed full system inspection with burner assembly operating properly, displaying clean blue flame combustion across all burner ports. Verified gas valve operation, inspected electrical connections including ignition control wiring, and confirmed proper venting configuration. Conducted temperature differential measurements using digital combustion analyzer, confirming system performance within manufacturer specifications. All components functioning correctly with no deficiencies noted at time of service.

Completed comprehensive tune-up and safety inspection on 21-year-old steam boiler system. Verified all operational parameters, confirmed proper combustion efficiency, and ensured system is functioning safely for continued reliable heating performance.

Responded to no heat call on 2-year-old furnace in basement. Upon inspection, found unit running but blowing cold air only. Diagnosed failed control board with error code displayed on LED. Inspected all wire connections to board terminals, verified proper voltage supply, and confirmed ignition sequence was not initiating. Control board replaced and system tested successfully, restoring proper heating operation.

Installed new Navien NPE-240A2 tankless water heater with recirculation system to replace existing conventional water heating unit. Replaced existing expansion tank with new S12 4.5-gallon water heater expansion tank during installation. All copper piping connections, brass fittings, and pressure relief components were properly installed and tested for proper operation.

Drained and isolated the hydronic heating system to perform necessary copper pipe repairs. Completed line repairs with proper soldering techniques, then refilled the system and purged all air from the lines to restore proper operation. System tested and confirmed operational with no leaks detected at repair points.

Responded to emergency plumbing call for active water leak penetrating through second floor ceiling with visible bulging. Upon investigation, identified compromised piping in crawlspace above affected area, evidenced by water staining on ceiling surface and aged copper supply lines showing deterioration. Accessed plumbing assembly beneath floor joists, inspected NIBCO valve connections, shutoff valves, and associated copper and PVC piping for failure points. Isolated water supply using existing red-handle shutoff valve to stop active leak. Assessed bathroom fixtures including tub spout and shower valve for related issues, noting mineral buildup and age-related wear on chrome fixtures. Documented existing conditions of plumbing system, structural water damage to ceiling material, and compromised pipe sections requiring repair or replacement to prevent further water intrusion.

Responded to no-heat call on 35-year-old furnace and identified cracked heat exchanger requiring immediate replacement for safety. Provided customer with equipment replacement estimate and documented existing HVAC system configuration including furnace, ductwork, and surrounding mechanical equipment in basement utility area.

Responded to service call for leaking pipe in upstairs bathroom sink causing water damage to ceiling below. Upon inspection, identified compromised supply line connection at vanity faucet assembly. Shut off water supply, removed failed connection, installed new compression fitting, and pressure tested system to verify proper seal and eliminate leak.

Performed scheduled boiler maintenance and system inspection in response to service call. Documented mechanical components including heat exchanger coils showing age-related oxidation, piping connections, valves, and mounting hardware to verify operational status and identify any required follow-up maintenance.

Completed standard tune-up maintenance on a 30-year-old furnace system. Upon inspection, discovered significant deterioration and rust damage to the heat exchanger, with visible cavities and corrosion present. Documented the compromised condition with photos showing extensive weathering, discoloration, and structural degradation that poses potential safety concerns for continued operation.

Responded to service call for tanked water heater leaking from top connections following recent tank flush. Upon inspection, found A.O. Smith ProMax water heater with significant corrosion and rust buildup at top fitting connections and center access panel, indicating long-term moisture exposure that likely worsened after flushing procedure disturbed sediment and stressed compromised fittings.

Performed scheduled maintenance on residential hot water tank including complete flush and fill procedure to remove sediment buildup and maintain optimal heating efficiency. Inspected associated plumbing connections, expansion tank, and system components for proper operation and confirmed all equipment functioning within normal parameters.

Completed full Unico high velocity AC system installation including smart high-efficiency blower module, coated evaporator coil module for extended longevity, and new Bryant outdoor condensing unit. Installed new condenser pad with gravel base, electrical disconnect box mounted to exterior wall, and drain pan equipped with safety switch. Reused existing thermostat and added three additional supply outlets to optimize airflow distribution throughout the system. Replaced and enlarged the first two feet of supply ductwork per Unico specifications to ensure proper system performance. All refrigerant lines connected with brass fittings and properly insulated, unit secured on composite pad with appropriate clearances from structure. System tested and operational.

Responded to emergency call for second-floor bathtub drain leaking through kitchen ceiling. Upon arrival, accessed the drain line from the basement utility area and identified the leak source in the vertical drain stack. Performed drain line repair to stop active water infiltration. Inspected surrounding plumbing infrastructure including copper supply lines and drainage system to ensure no additional compromises. Tested repaired drain line under full water flow to verify leak was eliminated and proper drainage function was restored. Advised homeowner to monitor ceiling area for any residual moisture and confirmed all plumbing systems were operating normally before completing service.

Installed and connected gas line to wall-mounted garage heater unit. Ran black iron pipe from existing gas supply, secured all connections with proper fittings, and pressure tested system to ensure leak-free operation. Heater is now fully operational and ready for use.

Responded to no-heat call at residential property with 3-year-old furnace system. Upon arrival, inspected White-Rodgers programmable thermostat and verified system settings, display functionality, and temperature differential. Examined furnace unit and associated ductwork in mechanical space, checking for proper operation and any visible issues with gas supply lines and ventilation components. Diagnosed thermostat communication issue preventing furnace from receiving proper call for heat. Restored heating system to full operation and verified proper cycling and temperature control.

Responded to no hot water complaint on residential tanked water heater. Upon arrival, confirmed pilot light operational but main burner failing to ignite. Customer had previously replaced thermocouple, thermal safety switch, and cleaned air baffle assembly without resolution. Performed diagnostic assessment of gas control valve and burner assembly. Determined gas control valve malfunction preventing gas flow to main burner despite functional pilot and proper thermocouple signal. Replaced defective gas control valve and tested system operation through multiple heating cycles. Verified proper ignition sequence, flame characteristics, and temperature rise. Unit restored to full operational status with adequate hot water production.

Provided quote for temporary removal and reinstallation of tanked water heater to accommodate excavation work on property. Assessed existing water heater installation including PEX and copper supply line connections, shut-off valves, and current mounting configuration on concrete platform to determine scope of disconnection and reconnection procedures. Installed new pedestal sink in bathroom with chrome faucet fixtures and completed all supply line connections. Verified proper drainage and tested faucet operation to ensure leak-free installation. Diagnosed slow-filling toilet to identify cause of reduced fill rate and provided recommendations for repair.

Conducted comprehensive evaluation of existing HVAC system including Armstrong Ultra V furnace unit and associated ductwork infrastructure in basement mechanical room. Documented current equipment condition, noting age-related wear on flexible ductwork with dust accumulation, and assessed overall system configuration including water heater and expansion tank setup. Provided detailed replacement estimate for complete system upgrade to address equipment lifecycle and efficiency concerns.