HVAC & Plumbing Services in Cleveland Heights, OH

Responded to service call for recently installed furnace (January) that was not operating. Upon inspection, verified proper ignition with strong blue flame visible in sight glass. Checked gas valve assembly, connections, and wiring - all components now functioning correctly. System operational and heating effectively.

Performed inspection on 10-year-old natural gas boiler as requested by customer prior to extended absence. Examined water level in sight glass, which was found to be full. Checked valve assembly and associated plumbing components, ensuring proper functionality of the system. All components operating within normal parameters; no issues requiring immediate attention were identified.

Diagnosed garage heating system with Johnson Controls A419 temperature controller showing readings of 143-164 degrees. Inspected and adjusted controller settings to restore proper heat output on 9-year-old heating unit. Verified system operation and confirmed proper temperature regulation through the digital controller.

Successfully installed twelve (12) 3/4" ball valves on copper piping manifold system mounted on concrete block wall. All valves were properly secured, tagged for identification, and tested for proper operation.

Successfully replaced two deteriorated water shut-off valves in basement with new quarter-turn ball valves, ensuring proper functionality and preventing potential leaks. Also performed drain cleaning service on bathtub drain using professional snake equipment to clear blockage and restore proper drainage.

Diagnosed and replaced leaking pressure gauge on boiler system. Visual inspection confirmed corrosion at copper pipe connection point causing the leak. Installed new Milioco pressure gauge and verified proper system pressure readings.

Responded to service call for 10-year-old residential boiler with automatic shutoff malfunction. Diagnosed and repaired site gauge issue affecting water level monitoring system. Inspected heat exchanger tubes and burner assembly, noting normal wear consistent with unit age.

Conducted furnace replacement estimate for aging HVAC system located in basement utility area. Inspected existing Aprilaire humidifier system, ductwork configuration, and electrical service panel to determine compatibility requirements for new equipment. Documented current installation conditions to provide accurate replacement options.

Performed scheduled maintenance flush on three tanked water heaters (including one Hotpoint model) to remove sediment buildup and maintain optimal system efficiency. Inspected all units, connections, and venting systems for proper operation. All water heaters now functioning correctly with improved performance and extended service life.

Performed scheduled preventative maintenance on residential boiler system. Conducted thorough inspection of heating infrastructure including examination of distribution pipes and mounting hardware in basement area. All components functioning within normal parameters with no issues detected.

Inspected existing boiler system and identified faulty thermocouple component. Removed damaged assembly with coiled copper tubing and replaced with new brass thermocouple to restore proper temperature sensing functionality. System tested and confirmed operational.

Conducted furnace replacement estimate for 25-year-old unit showing significant wear and dust accumulation. Inspected existing system including ductwork configuration and connections in basement utility area. Documented current installation with photos to develop appropriate replacement options for this aging residential heating system.

Diagnosed newly installed boiler (3 weeks old) that was non-operational. Identified mounting bracket failure due to deteriorated concrete foundation causing improper alignment of unit. Secured equipment with appropriate bolting hardware and documented structural issues requiring future concrete repair.

Performed scheduled Heating Tune Up on system under Home Plan coverage. Conducted temperature differential testing showing 124.3°F at supply register. Inspected and verified proper operation of blower motor assembly and electrical connections - all components clean with no signs of wear or damage.

Performed routine maintenance on 4-year-old MVP furnace system. Inspected all internal components with front panel removed, examined PVC venting system, and checked connections to ductwork. System is functioning properly with no issues detected.

Responded to service call for non-functioning boiler with water leak from pipe. Upon inspection, determined this was a plumbing issue rather than an HVAC concern. Service call was incorrectly categorized as boiler maintenance when it required plumbing expertise instead.

Responded to no heat call for 20-year-old furnace. Conducted combustion analysis using Testo 310 analyzer to evaluate system efficiency and safety parameters. Readings indicated proper operation after service was completed, restoring heat to the residence.

Accessed bathroom plumbing system by opening wall adjacent to toilet to expose leaking 2" cast iron pipe. Removed damaged section and replaced with new PVC piping, ensuring proper connections and sealing. Completed functional testing to verify repair eliminated the leak.

Diagnosed furnace showing green and red indicator lights with insufficient heat output. Inspected heat exchanger which showed warm water circulation but not reaching proper temperature. Cleaned accumulated debris from underside components and restored proper heating function by adjusting flow parameters.

Performed inspection of aging plumbing system in crawl space/basement area. Observed multiple copper pipes showing significant corrosion and deterioration alongside PVC piping. Identified potential water damage to wooden joists in ceiling structure. Visual assessment completed to determine necessary repairs for future service.