HVAC & Plumbing Services in Cleveland Heights, OH

Responded to service call for steam boiler system at owner-occupied residence. Upon arrival and inspection, identified damaged pipe insulation on steam distribution line, which was allowing heat loss and potentially affecting system efficiency. Documented existing cast iron radiator condition and steam pipe insulation deterioration. Advised property owner of insulation repair needs to prevent continued energy loss and maintain proper steam delivery to heating zones throughout the residence.

Technician arrived on-site to address customer questions regarding a previously quoted mini split installation and to assess optimal placement locations. Interior and exterior evaluations were conducted of the proposed installation area, including review of wall structure, ceiling configuration, and exterior mounting options on the gray shingled section of the residence. Installation feasibility confirmed and placement recommendations provided to customer.

Completed routine cooling system maintenance on a 12-year-old Lennox residential air conditioning unit, model C33-36C-2-6. Performed comprehensive inspection of outdoor condenser unit, verified refrigerant lines and connections, documented equipment condition with photographs, and confirmed system operational status per manufacturer specifications.

Performed comprehensive AC tune-up on 15-year-old cooling system operating normally. Completed full system diagnostics using refrigerant manifold and micron gauge, measuring pressures, superheat, subcooling, and saturation temperatures at outdoor condenser unit. All readings confirmed proper refrigerant charge and system performance within manufacturer specifications.

Conducted on-site evaluation for mini split installation in kitchen area with potential expansion to additional zones. Assessed existing electrical panel capacity and available breaker spaces to determine power requirements for proposed ductless system. Evaluated installation location near kitchen window area and identified suitable routing paths for refrigerant lines and electrical connections. Documented current electrical infrastructure and potential mounting locations for indoor and outdoor units. Provided customer with equipment options and installation scope for single or multi-zone mini split configuration.

Completed routine seasonal air conditioning tune-up on a 13-year-old Umco cooling module system (Model MC4860CX) utilizing R-410A refrigerant. System was found operating properly with all components functioning within normal parameters; performed standard preventive maintenance procedures including inspection of electrical connections, refrigerant pressures, and overall unit operation to ensure continued reliable performance.

Collected payment for completed HVAC repair work on basement heating system with boiler unit and Amtrol expansion tank. Documentation photos taken and forwarded to warehouse for records.

Completed preventive maintenance tune-up on two residential air conditioning systems: a 15-year-old unit and a 10-year-old unit, with one located in the basement and one positioned outside. Performed comprehensive inspection of both systems including blower motor assemblies, examined electrical connections and wiring, verified proper motor operation, and assessed cooling fan components which showed normal dust accumulation consistent with equipment age and use. Both systems found to be in operational condition following standard maintenance procedures.

Performed comprehensive air conditioning tune-up on approximately 20-year-old outdoor unit. Conducted system diagnostics and measurements using digital testing equipment, verified operational parameters, and completed preventive maintenance procedures to ensure proper cooling performance.

Responded to service call for clogged sink drain and low hot water pressure. Upon inspection, discovered significant mineral buildup and sediment accumulation in plumbing fixtures. Cleared blockage from sink drain line using appropriate drain cleaning equipment. Identified corroded internal tank components and discolored water indicating mineral deposits affecting water flow. Addressed hot water pressure issue by flushing sediment from supply lines and inspecting aerators. Restored proper drainage to sink and improved hot water pressure to normal operating levels.

Responded to boiler repair call for 10-year-old unit at owner-occupied residence. Upon arrival, inspected boiler control system and accessed main electrical enclosure containing dual circuit boards with LED indicators and multi-colored wiring harnesses. Evaluated control board functionality, verified proper electrical connections at terminal strips, and confirmed all indicator lights were operational. System tested and returned to normal operation with no component replacements required at this time.

Responded to no-heat call for 20-year-old furnace. Upon arrival, performed diagnostic inspection and found unit was not igniting. Checked electrical connections, gas supply, and ignition system components including flame sensor and burner assembly. Cleaned flame sensor rod and verified proper positioning over burner ports. Cycled unit and confirmed successful ignition with proper blue flame pattern across all burners. Verified all safety controls functioning correctly and unit operating within normal parameters. System restored to full heating operation.

Responded to water leak in basement of 106-year-old residential property. Upon arrival, located source of leak in crawl space beneath main floor. Inspection revealed severely corroded galvanized steel supply piping with extensive rust deterioration at multiple joints and valve connections. Primary leak originated from compromised vertical pipe section where corrosion had penetrated through pipe wall at coupling assembly. Shut off main water supply to prevent further water damage. Removed failed corroded pipe section and associated fittings exhibiting structural compromise from rust buildup and mineral deposits. Cut out approximately four feet of deteriorated galvanized piping. Installed new copper pipe section with compression fittings and brass shutoff valve to replace corroded assembly. Secured new piping to floor joists with appropriate hangers and supports. Tested system for leaks by restoring water pressure and monitoring all connections for twenty minutes. Verified no active le

Performed preventative maintenance on two residential cooling systems: one outdoor condenser unit located in the backyard and one air handler unit installed in the attic space. Conducted temperature diagnostics on the outdoor unit, recording surface temperature readings of 54.5°F on the condenser pad. Inspected condenser coil fins, concrete pad condition, and overall exterior unit operation. In the attic, evaluated the air handler system including flexible ductwork connections, insulated refrigerant line sets, PVC condensate drainage system, and auxiliary condensate pump assembly. Verified proper installation of all components, checked insulation integrity on refrigerant lines, and confirmed condensate removal systems were functioning correctly. Both systems appeared operational with all major components accessible for routine service.

Responded to emergency call for frozen anti-frost spigot installed the previous year with suspected burst pipes. Upon arrival, inspected exterior spigot mounted on brick wall and accessed crawl space to evaluate copper supply line condition. Found compromised pipe insulation and deteriorated vapor barrier mesh in underfloor area. Assessed brass fittings and copper piping for freeze damage, verified structural integrity of plumbing connections, and documented conditions of both exterior spigot installation point and interior supply line routing through floor joists.

Responded to no heat call on an eight-year-old furnace. Upon arrival, performed diagnostic testing using digital multimeter to check electrical components and thermocouple voltage readings, which measured 0.18V indicating a failed thermocouple. Replaced faulty thermocouple assembly, restored proper millivolt signal to gas valve, and verified furnace ignition sequence and heating operation throughout the home.

Completed professional installation of customer-supplied kitchen sink in granite countertop over a two-day service period. Installation included mounting stainless steel double-basin sink, installing modern single-handle pull-down faucet with brushed metal finish, and configuring complete under-sink plumbing assembly with garbage disposal unit, PVC P-trap drainage system, copper water supply lines, and shut-off valves. All components tested and verified operational upon completion.

Completed annual preventive maintenance on one-year-old air conditioning system. Performed comprehensive system diagnostics using refrigerant manifold gauges to measure operating pressures, temperatures, superheat, and subcooling values, confirming all parameters within manufacturer specifications for optimal cooling performance.

Completed comprehensive maintenance on 22-year-old air conditioning system and 21-year-old gas furnace. Performed full system inspection including evaporator coil cleaning, condenser coil assessment, refrigerant line inspection, and blower motor evaluation in response to customer concerns about potential blower issues. All components photographed and documented, with particular attention to coil condition and refrigerant connections showing age-appropriate wear on copper lines and insulation.

Responded to service call for multiple plumbing fixtures requiring repair. Addressed dripping faucets throughout the property, including the wall-mounted three-piece bathroom faucet assembly with dual lever handles and center spout. Diagnosed and corrected shower temperature fluctuation issue caused by pressure imbalance in the mixing valve. Repaired continuously running toilet by replacing faulty flapper valve and adjusting fill valve mechanism to restore proper water shutoff function.