HVAC & Plumbing Services in Cleveland Heights, OH

Completed installation of Gerber Avalanche ADA elongated toilet with new seat, wax ring, and supply line in bathroom. Pulled and reset under-counter mount kitchen sink, securing mounting hardware and reconnecting water supply lines and drain assembly. Replaced Kohler shower cartridge in master bathroom shower valve to restore proper temperature control and water flow.

Responded to air conditioning system not cooling to set temperature with indoor temperature at 79°F and thermostat set to 68°F. Upon inspection, discovered extensive accumulation of organic debris, nesting material, leaves, and plant matter throughout the outdoor unit's electrical compartment surrounding wiring and components. Removed all debris from electrical compartment and verified proper operation of start relay and electrical connections. Inspected attic-mounted air handler unit, condensate pan, and ductwork for proper operation. Cleared vegetation from around outdoor unit perimeter to prevent future debris intrusion. System tested and confirmed cooling operation restored to normal parameters.

Returned to complete scheduled maintenance after unit experienced frozen evaporator coil on initial visit. Allowed system to fully thaw before proceeding with diagnostic testing. Utilized refrigerant manifold gauge set to verify system pressures and temperatures, confirming proper refrigerant charge and operational parameters upon completion of thaw cycle.

Completed routine maintenance on Bryant air conditioning system. Performed standard inspection of outdoor condenser unit and air handler, verifying proper operation of all components. System found to be operating within normal parameters with no issues identified during service visit.

Completed routine maintenance on a 4-year-old residential air conditioning system. Performed comprehensive inspection of outdoor condenser unit, checked refrigerant levels and pressures using diagnostic equipment, cleaned condenser coils, verified electrical connections, and tested system operation to ensure optimal cooling performance.

Returned to address ongoing system failure following previous service visit last week. Outdoor condensing unit still not operational despite prior repair attempt. Conducted diagnostic evaluation of residential air conditioning system installed at exterior brick wall location. Further troubleshooting required to identify and resolve persistent malfunction preventing unit from cooling properly.

Conducted comprehensive estimate for complete HVAC system replacement at residential property. Evaluated existing furnace installation in basement utility area with connected ductwork system and outdoor AC condenser unit mounted against exterior wall. Documented current equipment configuration, assessed installation requirements, and provided replacement recommendations for both heating and cooling systems.

Conducted on-site assessment for mini split installation to replace existing window air conditioning units in residential space. Evaluated room layout, electrical requirements, and optimal placement for indoor unit mounting, marking proposed location on wall. Also performed estimate for gas line installation to service kitchen stove.

Completed on-site estimate for add-on air conditioning system to complement existing furnace heating equipment. Assessed electrical panel capacity and available circuit breaker positions for new AC unit installation, documented current wiring configuration and main disconnect switch. Evaluated basement mechanical room layout, measured available clearances including 11-foot dimensional requirements, and verified adequate space for condensate drainage, refrigerant line routing, and proper equipment placement alongside existing HVAC infrastructure.

Completed routine maintenance tune-up on 5-year-old residential air conditioning system. Performed standard diagnostic testing and system inspection of outdoor condenser unit, including electrical measurements and operational checks. Unit found to be functioning within normal parameters with no immediate repairs required.

Responded to a leak in the cold water supply line servicing an upstairs toilet. Upon arrival, inspected the affected plumbing system and traced the source of the leak. Repaired the compromised cold water line connection to restore proper water supply to the fixture and verified all connections were secure with no active leaks present. System tested and confirmed operational upon completion.

Responded to water leak in basement of century-old residential property. Upon arrival, inspected plumbing system and identified active leak at threaded pipe connection in overhead piping assembly. The galvanized metal elbow joint showed deterioration consistent with the age of the home's infrastructure, with compromised threading allowing water seepage at the connection point. Shut off water supply to affected area and disassembled the leaking elbow fitting. Cleaned threaded surfaces and removed old deteriorated sealant material. Applied new blue PTFE thread seal tape to male threads according to proper wrapping technique. Reassembled the pipe connection, ensuring proper torque to create watertight seal without over-tightening which could damage aged threading. Restored water supply and pressure-tested the repair by running water through the system while monitoring the connection point for any signs of moisture or dripping. Confirmed repair was secure with no active leakage detected.

Conducted comprehensive on-site evaluation for add-on air conditioning system installation to existing forced-air heating infrastructure. Assessed current ductwork configuration, plenum connections, and available space in mechanical room to determine optimal placement and integration points for new cooling equipment. Documented existing furnace/air handler setup, including cabinet-style unit with decorative grille, supply and return duct pathways, and insulated ductwork runs to facilitate proper AC coil installation and refrigerant line routing for seamless system integration.

Responded to service call regarding recently installed mini split unit with reported door gap issue. Upon inspection, examined indoor air handler unit mounted near decorative ceiling area and verified operational status. Documented unit condition with photographs showing proper mounting and clearances. Unit appears to be functioning as designed with no immediate mechanical concerns observed at time of visit.

Completed scheduled cooling system tune-up and preventive maintenance on residential HVAC system. Performed comprehensive inspection of Bryant furnace and cooling components, verified proper operation of all equipment, checked refrigerant levels, cleaned condensate system, and inspected ductwork connections for proper airflow and seal integrity.

Performed cooling maintenance tune-up on dual central air system serving second and third floors. Addressed reported rhythmic noise issue from upper-level unit, inspected both systems, and completed standard preventive maintenance procedures including filter checks, refrigerant level verification, electrical connections inspection, and condenser coil cleaning of exterior unit.

Arrived on-site for scheduled AC maintenance on 7-year-old system originally installed in 2019. Performed comprehensive inspection of outdoor condensing unit and indoor air handler components. Inspected blower wheel assembly, confirming clean operational condition with minimal dust accumulation and proper motor shaft alignment. Measured system operating temperature at 73.5°F and conducted refrigerant pressure diagnostics using manifold gauges. All components found to be functioning within normal parameters with no water leaks detected or service issues identified during inspection.

Completed full HVAC system replacement including furnace removal and installation, added new air conditioning system with outdoor condensing unit, ran new refrigerant line set and dedicated electrical circuit for A/C operation, installed 700 CFM return air grille, and programmed Ecobee smart thermostat. System was pressure tested, charged to manufacturer specifications, and verified operational with all safety controls functioning properly.

Responded to service call for Rheem RTGH-95DVLN-2 tankless water heater with sensor alert and no hot water production. Inspected internal components including heat exchanger assembly, electrical connections, control board, and venting system. Diagnosed sensor malfunction, performed necessary repairs to restore unit functionality, and verified proper operation of all system components including gas valve, ignition system, and water flow.

Responded to no cooling complaint at apartment 4 for a 9-year-old air conditioning system. Upon arrival, performed visual inspection of outdoor condenser unit, which showed significant accumulation of dirt, dust, and debris on coil fins affecting heat transfer efficiency. Conducted diagnostic testing using digital multimeter to verify electrical components and system operation. Assessed condenser unit mounted on concrete pad with evidence of weathering and environmental exposure. Evaluated indoor air handling components and ductwork connections. System restored to proper cooling operation following service procedures.