HVAC & Plumbing Services in Cleveland Heights, OH

Installed new InSinkErator Pro Series garbage disposal unit in kitchen of 95-year-old home. Completed full installation including mounting assembly, drain connections, and P-trap configuration with PVC piping. Repaired leaking bathroom faucet to restore proper operation and eliminate water waste.

Responded to service call for 9-year-old central air conditioning system not cooling. Upon inspection of rooftop condenser unit and indoor Goodman furnace/air handler, diagnosed and resolved cooling issue. System tested and confirmed operational with proper airflow and refrigerant cycling restored.

Responded to callback for air conditioning system not cooling. Upon arrival, inspected HVAC system and ductwork in attic space. Found issue with flexible duct connections and sealing at air handler unit. Resealed duct joints with metallic tape to eliminate air leakage. Verified proper airflow through supply ducts and checked foil-faced insulation integrity around distribution channels. System tested and confirmed operational with adequate cooling performance restored.

# HVAC Complete System Installation Successfully completed a full HVAC system replacement in a basement mechanical room. Installed new furnace with matching evaporator coil and air conditioning condenser unit. Ran new refrigerant line set to connect outdoor condensing unit to indoor coil. Installed dedicated electrical circuit and disconnect for air conditioning system to meet code requirements. Mounted new programmable thermostat and completed wiring to new equipment. Reconnected existing return air ductwork from previous Cleveland drop installations to new furnace plenum. All ductwork connections were properly sealed and insulated where required. System was charged to manufacturer specifications, tested for proper operation across all modes, and confirmed adequate airflow throughout the home. Equipment is operating efficiently within normal parameters.

Responded to service call for non-functional outdoor spigot with hose connection issues. Removed and replaced the existing decorative outdoor faucet fixture, which featured a bird ornament design and was mounted on the exterior wooden surface below the building's siding. Installed new spigot assembly, ensured proper sealing and connection to supply line, tested water flow and verified no leaks at connection points.

Responded to emergency plumbing call for active backflow device leak with constant water flow in 98-year-old residential property. Assessed backflow preventer in basement utility area and documented existing conditions with photographic evidence. Due to age of plumbing system and severity of leak, recommended immediate repair or replacement of failed backflow assembly to prevent water damage and restore proper system function.

Responded to service call for non-operational air conditioning system affecting entire residence. Upon arrival, assessed both indoor furnace/air handler unit located in basement mechanical room and outdoor condensing unit positioned against exterior wall. Documented existing equipment configuration including electrical disconnect, refrigerant line set routing, condensate drainage system, and current installation setup. Provided comprehensive estimate for complete HVAC system replacement including removal of existing equipment, installation of new high-efficiency air conditioning system, and all associated components necessary to restore cooling functionality to the home.

Responded to service call for 27-year-old furnace system with reported grounding issue. Upon arrival, performed diagnostic inspection and confirmed electrical wiring deficiency requiring immediate attention. Replaced faulty wiring to furnace unit and corrected improper grounding condition to restore safe operation and bring system up to code. System tested and verified operational following repairs.

Completed comprehensive tune-up on 10-year-old residential air conditioning system. Performed standard maintenance protocol including system diagnostics using Fieldpiece digital gauges to verify refrigerant pressures and temperatures across the evaporator coil, with all readings indicating proper system operation. Utilized UEi digital measuring instruments to assess additional system parameters and confirm optimal performance of the outdoor condensing unit.

Responded to service call for non-operational air conditioning system. Upon arrival, performed comprehensive AC tune-up and system diagnostic. Identified significant condensation accumulation on interior glass surfaces, indicating excessive indoor humidity levels and potential system performance issues. Verified thermostat operation and display functionality showing current temperature readings. Inspected refrigerant levels, electrical connections, and overall system operation to restore cooling capacity. System returned to normal operating condition with proper cooling output achieved.

Completed scheduled maintenance on both central air conditioning system and mini split unit, both approximately 4 years old. Performed comprehensive tune-up procedures including inspection of coil module, verification of R-410A refrigerant specifications, and assessment of electrical connections and ductwork. All systems operating within normal parameters upon completion of maintenance service.

Provided estimate for mini split installation in residential property with dark wood trim and white walls. Assessed multiple interior locations for optimal unit placement, including entryway area with console table and main living space with double-paned windows. Also evaluated site requirements for tankless water heater installation to replace existing system.

Performed comprehensive routine maintenance on a 15-year-old Rheem air conditioning system (Model RCFL-194482ACC, Serial MG91069758, manufactured 07/2010). Inspected indoor air handler unit located in basement mechanical room and outdoor condensing unit. System was operating properly with no reported issues prior to service. Completed standard AC tune-up procedures including visual inspection of all components, verification of proper airflow through ductwork, checking refrigerant levels, cleaning condenser coils, inspecting electrical connections, and testing system operation. All equipment found to be functioning within normal parameters. Documented equipment condition with photos of indoor unit and manufacturer data plate for maintenance records. System cleared for continued operation with recommendation to monitor performance given age of equipment.

Responded to callback for no airflow issue in dining room and living room following previous no cool service call. Upon inspection, discovered airflow restriction in ductwork system serving affected zones. Investigated basement mechanical area and identified damper positioning or ductwork obstruction preventing proper air distribution to specific supply vents. Adjusted system components and verified adequate airflow restoration to all previously affected areas. System now operating properly with balanced air distribution throughout conditioned space.

Responded to service call for moisture concerns on 2-3 year old AC unit with reported pipe wicking. Upon inspection, found condensate drainage system experiencing moisture accumulation around indoor air handler unit in basement mechanical room. Concrete floor showed extensive water staining and discoloration patterns indicating ongoing moisture issues. Examined drain pan, condensate lines, and insulation for proper installation and function. Documented conditions with photos showing equipment installation, floor staining, and moisture damage patterns. Recommended monitoring system for proper drainage and potential dehumidification solutions to address basement moisture levels affecting unit performance.

Completed comprehensive tune-up maintenance on a 20+ year old residential HVAC system operating within normal parameters. Performed standard maintenance protocol including inspection of blower assembly and squirrel cage fan wheel, which showed clean condition with no debris accumulation or component wear. System confirmed to be functioning properly with all components operating as designed.

Responded to follow-up service call for tanked water heater that experienced loss of hot water after previous repair completed on 4/27. Upon arrival, performed comprehensive inspection of water heater system, including all copper supply lines, gas connections, venting assembly, electrical components, and associated plumbing infrastructure. Documented current condition of equipment with photographs showing water heater installation with proper venting through corrugated metal exhaust duct, multiple copper pipe connections at varying diameters, and black rubber connector hoses. Assessed entire mechanical system including overhead ductwork, PVC piping, and utility room configuration to identify root cause of recurring hot water failure.

Conducted estimate for replacement of approximately 25-year-old steam boiler system currently in operation. Evaluated existing equipment and discussed power vent conversion options as an alternative to traditional chimney venting, per customer's preference and willingness to eliminate existing chimney infrastructure. Documented current boiler configuration, piping network including copper and black iron steam lines, and existing venting arrangement to provide comprehensive replacement options and specifications.

Completed comprehensive plumbing assessment in residential property requiring difficult access to equipment located in attic/crawl space area. Two-person crew relocated homeowner belongings to access vertical cast iron waste stack with blue shut-off valve and transitioned PVC connections secured with metal hose clamps. Acquired necessary permit and installed miscellaneous materials to complete repair work on plumbing infrastructure within exposed framing area.

Completed installation of dual-zone air conditioning system consisting of two outdoor condensing units, two indoor evaporator coils, and two sets of refrigerant line sets. Installed two condenser pads for equipment placement, two electrical disconnect boxes, and ran two dedicated electrical circuits to power the new units. Mounted two condensate pumps for proper drainage management and installed two programmable thermostats for independent zone control. Fabricated and installed open return ducting for first floor air circulation, connecting to the first floor air handler. All refrigerant lines were properly insulated, vacuum tested, and charged to manufacturer specifications. Electrical connections were completed in accordance with local code requirements, and all equipment was tested for proper operation and performance.