HVAC & Plumbing Services in Cleveland Heights, OH

Replaced evaporator coil on wall-mounted ductless mini-split system under parts warranty coverage. Completed all necessary refrigerant line connections, condensate drainage, and electrical connections to restore unit to proper operation.

Responded to customer report of water hammer (banging pipes) that began following exterior water shutoff work. Installed pressure gauge on exterior hose bib to diagnose system pressure issues potentially contributing to both the pipe noise and previously reported running toilet. Pressure reading indicated near-zero static pressure at exterior fixture, suggesting possible pressure regulation concerns that may require further investigation to resolve both the water hammer condition and toilet fill valve operation.

Performed gas leak and pressure test on residential gas line system in preparation for new stove installation. Upon arrival, confirmed gas service to home was shut off at meter. Conducted thorough visual inspection of existing gas piping, including flexible gas connector and brass fittings at furnace connection point. Tested all accessible gas line connections and joints for leaks using approved testing methods. Verified proper gas valve operation and assessed gas line routing for code compliance. Inspected flexible corrugated stainless steel gas line condition and connection integrity at HVAC equipment. All tested connections passed pressure test with no leaks detected. System confirmed ready for new appliance hookup and gas service restoration.

Completed furnace and thermostat replacement in basement mechanical room. Successfully removed existing furnace unit and installed new replacement furnace, reconnecting to existing ductwork and utilizing existing air handler, filter rack, and air conditioning system. Installed new thermostat, verified all electrical connections, tested system operation, and confirmed proper functionality of heating cycle.

Completed comprehensive MVP heating tune-up on gas-fired HVAC system in basement utility area. Performed full system inspection including burner assembly, heat exchanger, blower motor, and ductwork connections; verified proper gas pressure, cleaned burner components, tested safety controls, and confirmed all mechanical and electrical systems operating within manufacturer specifications. System is functioning efficiently with no issues identified.

Completed comprehensive tune-up on 15-year-old residential furnace system. Performed standard maintenance protocol including inspection of all internal components, electrical connections, and wiring integrity. Noted significant rust and corrosion present on metal piping and internal compartment surfaces, indicating moisture exposure over time. Observed accumulated dust and debris throughout cabinet, which was cleaned during service. Verified proper operation of transformer, relay components, and all electrical connections. Inspected exterior condensing unit, noting deteriorated top panel with organic growth, environmental debris accumulation, and mildew present on surfaces. Unit currently operating within normal parameters despite age-related wear and corrosion issues. Recommended monitoring moisture sources contributing to internal rust formation and consideration of future component replacement due to advanced corrosion. System left in proper working condition with all safety checks

Completed routine HVAC maintenance tune-up on residential heating and cooling system. Inspected gas furnace burner assembly, confirmed proper ignition and flame characteristics with all three burners operating efficiently. Verified heat exchanger condition, checked electrical connections and wiring, and documented system components. All equipment operating within normal parameters with no repairs required at this time.

Completed annual maintenance tune-up on 10-year-old boiler system. Performed comprehensive inspection of all components including heat exchanger, burner assembly, and combustion analysis using Testo 310 analyzer, which confirmed proper CO levels and combustion efficiency within manufacturer specifications. System found operating correctly with no deficiencies noted.

Performed comprehensive annual tune-up and maintenance on 12-year-old steam boiler system. Inspection included verification of gas valve operation, safety controls, electrical connections, and overall system functionality. All components found operating within normal parameters, with equipment showing expected wear consistent with age but maintaining proper working condition.

Performed comprehensive assessment of residential boiler and hydronic heating system for new homeowner. Inspected boiler unit, expansion tank, gas valve assembly, piping connections, and radiator distribution system. Documented existing equipment condition including aging components with visible corrosion and wear patterns on expansion tank and auxiliary equipment. Verified proper installation of safety controls and pressure relief systems. Provided homeowner with detailed findings regarding system age, current operational status, and recommendations for future maintenance considerations.

Completed full HVAC system replacement in residential basement installation, including new furnace, evaporator coil, air conditioning condenser unit, refrigerant line set, and air cleaner. All equipment installed to manufacturer specifications with proper electrical connections, gas piping, condensate drainage, and ductwork integration. System tested and verified operational with proper airflow, temperature differential, and refrigerant charge confirmed within acceptable parameters.

Responded to multiple plumbing issues throughout the residence. Cleared slow drains in the first-floor half bath, primary bathroom sink, and guest bathroom sink and tub using appropriate drain cleaning methods. Inspected and addressed the leaking showerhead in the primary bathroom, examining the shower arm mount and connection points where deterioration and gaps around the wall fixture were observed. Evaluated the faulty diverter lever on the guest bathroom tub faucet that controls water flow between the tub spout and showerhead. Additionally assessed the kitchen refrigerator water supply line to diagnose the water and ice dispenser malfunction. Documented conditions with photos showing shower fixture mounting concerns and tile grout deterioration requiring attention.

Responded to no-heat call for residential boiler system of unknown age located in basement mechanical room. Upon inspection, evaluated existing blue boiler unit with associated piping, flue system, and connections. Documented current equipment condition and configuration, including copper supply lines, yellow-insulated piping sections, metal ductwork, and venting system. Provided comprehensive estimate for complete boiler replacement to restore heating functionality to the property.

Completed comprehensive home plan plus maintenance inspection on residential heating boiler system. Performed thorough examination of heat exchanger components, including copper distribution tubes and fin assemblies, which showed moderate dust accumulation and surface oxidation consistent with normal operation. Documented equipment condition through visual inspection of all accessible components from maintenance access areas, including underside examination of primary heat exchanger sections and distribution manifold. All critical boiler components were assessed for proper operation and safety compliance per manufacturer specifications.

Responded to call for running toilet in 105-year-old residential home. Upon inspection, identified worn flapper valve causing continuous water flow into bowl. Replaced flapper assembly and adjusted fill valve height to ensure proper water level in tank. Tested flush mechanism multiple times to confirm proper operation and verified complete seal after tank refill, eliminating water waste issue.

# No Heat Service Call - 15-Year-Old Furnace Responded to a no heat call on a 15-year-old gas furnace. Upon inspection, found the unit's gas valve and associated piping showed significant corrosion and age-related deterioration. Verified ignition system was functioning properly with burners achieving proper flame characteristics. Assessed overall system condition, documented equipment wear, and confirmed unit was operational at time of service completion.

# Service Summary Completed assessment of gas water heater relocation requirements for upcoming residential remodel project. # Work Performed Responded to service call for gas water heater relocation assessment in preparation for customer's remodel work. Upon arrival, conducted thorough evaluation of existing gas-fired water heater installation, including current positioning within utility closet space, gas supply line configuration, and venting requirements. Documented existing water heater setup with detailed photographs showing current installation conditions. Unit is a standard atmospheric vent gas water heater with copper supply piping, properly installed drip pan, and gas line connection with shutoff valve. Assessed accessibility of current location and surrounding infrastructure including white PVC venting, hot and cold water distribution lines with shutoff valves, and gas supply routing. Evaluated potential relocation options within the space to accommodate remodel specifi

# Service Report: HVAC No Heat - Furnace Short Cycling ## Summary Responded to no heat call on 15-year-old furnace experiencing short cycling with burners igniting briefly then shutting down, resulting in cold air distribution. Diagnosed and resolved flame sensor issue causing premature safety lockout. ## Work Performed Upon arrival, confirmed customer complaint of furnace running for a few seconds before shutting off without producing heat. Performed visual inspection and operational test, observing ignition sequence initiating properly but burners extinguishing prematurely during heating cycle. Accessed furnace cabinet and inspected burner assembly, gas valve, ignition system, and flame sensing components. Identified flame sensor rod heavily coated with carbon buildup and oxidation, preventing proper flame rectification signal to control board. This condition caused control board to interpret lack of flame detection as unsafe operating condition, triggering safety shutdown. Remo

# HVAC Maintenance - Heating System Service Report Completed annual home plan maintenance inspection on a 6-year-old residential gas furnace system. Provided 30-minute advance notification to customer prior to arrival as requested. Upon arrival, performed comprehensive heating system inspection in accordance with manufacturer specifications and industry standards. Opened furnace cabinet to access internal components for thorough examination. Inspected heat exchanger for signs of cracks, corrosion, or deterioration. Verified proper operation of blower motor and checked for unusual noise or vibration. Examined all electrical connections, control boards, and wiring for secure terminations and signs of overheating or damage. Tested gas valve operation and verified proper ignition sequence. Inspected burner assembly for proper flame characteristics and even combustion. Checked flue pipe and venting system for proper installation and secure connections. Verified condensate drain lines wer

# Service Report Responded to no-heat call on residential boiler of unknown age. Upon arrival, confirmed unit had no power and would not initiate startup sequence. Conducted diagnostic inspection of boiler system and associated controls. Visual examination revealed significant corrosion on brass valve assemblies and connection points near the primary control relay (identified as model 9041). The deterioration of electrical connections and valve components indicated prolonged exposure to moisture and age-related degradation. Documented existing conditions with photographs showing corroded fittings, oxidized copper piping, and compromised wiring connections at the relay junction. Provided customer with diagnostic findings and recommended service options for system restoration. Customer to contact service department for follow-up regarding repair authorization.