HVAC & Plumbing Services in Cleveland Heights, OH

Responded to kitchen sink leak underneath fixture. Upon arrival, discovered extensive water damage affecting surrounding walls, ceiling, and structural components. Glass block window area showed signs of prolonged moisture exposure with deteriorated ceiling beams, compromised wall surfaces, and significant mold accumulation. Assessed leak source at sink base and evaluated extent of water intrusion damage to cabinet interior and adjacent building materials. Documented severe deterioration requiring immediate attention to prevent further structural compromise.

Responded to service call for leaking 40-gallon Bradford White residential water heater located in basement utility space. Upon inspection, identified active leak requiring unit replacement. Disconnected existing water heater from copper supply lines, gas line, and exhaust flue system. Removed failed unit and installed new 40-gallon water heater with proper venting configuration. Connected hot and cold water copper piping with appropriate brass fittings, installed pressure relief valve with discharge pipe, and reconnected gas supply line to burner assembly. Tested all connections for leaks, verified proper gas combustion, and confirmed temperature and pressure relief valve operation. System restored to full working condition.

Replaced failed condenser capacitor with new dual-run capacitor on outdoor HVAC unit. Verified proper system operation using refrigerant manifold gauges, confirming appropriate pressures and temperatures across the system. Unit tested and operating within manufacturer specifications.

Responded to emergency call for leaking water heater in 110-year-old residential property. Upon arrival, inspected four-year-old Bradford White tanked water heater installed in basement utility area and confirmed active water leak from unit. Documented existing installation configuration including copper supply lines with brass fittings, white PVC venting system, and current electrical connections via metallic flex conduit to junction box. Assessed leak severity and determined replacement necessary due to tank failure. Photographed existing installation setup, mechanical room conditions, and surrounding plumbing infrastructure for documentation purposes prior to recommending next steps for water heater replacement.

Responded to no cooling complaint on older R-22 refrigerant system. Confirmed R-22 systems can still be serviced and repaired despite refrigerant phase-out, though refrigerant costs are significantly higher than modern alternatives. Advised homeowner of available options including repair with reclaimed R-22 or future system replacement with newer R-410A equipment when economically appropriate.

Conducted on-site evaluation for mini split air conditioning installation in residential property currently equipped with steam boiler heating system. Assessed two interior rooms with existing windows to determine optimal placement for indoor air handling units, taking into account wall construction, electrical access points, and aesthetic considerations. Documented room dimensions, window configurations, and existing HVAC infrastructure to develop comprehensive equipment sizing and installation proposal for ductless mini split system.

Performed nitrogen leak search on residential air conditioning system and confirmed presence of refrigerant leak in system. Diagnostic testing identified leak location requiring repair to restore proper system operation and refrigerant charge.

Completed comprehensive cooling maintenance on two Carrier systems (11 years and 16 years old). Replaced air filters for AC, furnace, and humidifier units. Performed full AC tune-up including refrigerant pressure and temperature diagnostics using manifold gauges, verified system operating parameters, and inspected condenser coil condition. All systems tested and operating within manufacturer specifications.

Responded to water leak call at century-old residential property. Inspected plumbing system throughout home, including basement mechanical room with exposed PVC drainage lines, water heater connections, and bathroom fixtures. Documented conditions with photographs showing plumbing infrastructure and potential leak sources in aging system.

Completed return trip to system requiring additional technician support. Performed refrigerant system diagnostics using digital manifold gauges, recording operating pressures and temperatures. Left side pressure reading 100.6 PSI, right side pressure 245.2 PSI, with superheat at 14°F and subcooling at 82°F indicated on equipment. Monitored system performance parameters during severe weather conditions including heavy thunderstorms with temperatures in low 80s and high humidity levels at 94%.

Conducted on-site assessment for mini-split installation in bedroom. Evaluated electrical panel capacity and confirmed adequate breaker availability for new system. Measured and marked proposed indoor unit location on wall above bed at 9-foot height to ensure optimal air distribution and coverage for the space.

Responded to emergency no cooling call on three-week-old system. Replaced defective printed circuit board and restored full cooling operation. Verified proper system temperatures and confirmed unit operating within manufacturer specifications upon completion.

Completed full HVAC system replacement including installation of new Bryant 97% high efficiency gas furnace with single stage heating and multi-speed ECM blower motor. Installed new Bryant air conditioning system with outdoor condenser unit, indoor evaporator coil, concrete condenser pad, and electrical disconnect box. Ran new metallic ductwork through ceiling joists to accommodate system airflow requirements. Mounted condenser unit on pad against exterior wall with proper electrical connections and conduit routing. Existing thermostat was retained and reconnected to new equipment. All components tested and verified operational upon completion.

Responded to no cooling complaint on 7-year-old Heil central air conditioning system. Upon arrival, performed diagnostic evaluation using refrigerant manifold and micron gauge to assess system pressures and refrigerant charge. Testing revealed improper refrigerant levels on R410A system. Verified condenser coil condition, which appeared clean with good airflow. Corrected refrigerant charge to manufacturer specifications, monitored system pressures and temperatures to confirm proper operation, and restored cooling functionality to the unit.

Responded to no hot water condition in 104-year-old home where Lochinvar tank-type water heater displayed "thermopile voltage low" error message. Diagnosed failed thermopile assembly preventing gas valve operation and burner ignition. Replaced thermopile, verified proper millivolt output, tested gas valve functionality, and restored hot water service to entire house.

Conducted comprehensive on-site evaluation for complete HVAC system replacement in residential basement installation. Assessed existing Kenmore furnace unit and associated ductwork, documented current equipment configuration including air handler, plenum assembly, and galvanized metal ductwork with elbow connections. Photographed existing system components, mechanical room layout, and surrounding infrastructure to develop accurate replacement estimate for new furnace and air conditioning system.

Completed annual preventive maintenance on Fujitsu Halcyon mini-split heat pump system. Inspected outdoor condenser unit mounted on exterior wall, verified secure mounting brackets, checked refrigerant line connections, and confirmed proper drainage. Evaluated indoor wall-mounted air handler in bay window area, tested operational performance of both heating and cooling modes, and documented system condition with photographs for maintenance records.

Completed comprehensive HVAC replacement estimate for aging 21+ year old furnace and air conditioning system located in basement utility area. Assessed existing equipment condition, ductwork infrastructure, and calculated load requirements for planned second-story addition to determine proper system sizing and configuration needed to adequately heat and cool expanded living space.

Completed comprehensive AC tune-up on Bryant outdoor condensing unit and indoor air handler system. Performed thorough inspection of air filtration system and filter housing as requested, confirming proper fit, seal, and operational functionality. Verified FieldControls Healthy Home System air purification unit mounted in mechanical space is operating correctly with blue indicator light illuminated, confirming active air quality management. Conducted full preventive maintenance protocol including visual inspection of outdoor condenser coils, electrical connections, and refrigerant lines, with all components found in satisfactory working condition.

Completed warranty inspection and technical review of Unico system installation with manufacturer technical support consultation totaling 2.0 hours. Performed comprehensive attic assessment of ductwork and air handling components. Verified proper installation of outdoor condensing unit on equipment pad with appropriate clearances and electrical conduit routing. Confirmed condensate drain line installation with proper pitch and trap configuration. Inspected refrigerant line insulation integrity and support. All system components verified operational and installation meets manufacturer specifications.