South Euclid HVAC Services

Responded to service call for a customer-drilled hot water pipe. Upon inspection, found damage to copper hot water line behind teal/green beadboard wall. Cut access panel, replaced damaged section of pipe, and installed new shutoff valve with flexible supply line. Tested system for proper function and pressure.

Performed annual tune-up on 3-year-old furnace, measuring supply temperature (91.1°F) and return temperature (123°F). As requested, checked water pressure and verified cooling speed was set to high for optimal system performance.

Performed routine maintenance on 4-year-old heating system. Inspected blower motor assembly and fan operation for proper functionality. Examined furnace and air handler connection points, confirming proper ductwork installation and system integrity. All components operating within normal parameters.

Performed routine maintenance on two natural gas furnace systems. Identified and documented active water leakage from copper pipe connection with brass fitting. Conducted gas pressure testing with dual port manometer, recording readings of 150/154.

Performed scheduled maintenance on steam boiler system. Inspected copper piping, valves, and water level indicator, noting some surface corrosion and oxidation at connection points. Identified potential slow leak requiring future attention as evidenced by greenish-blue patina formation on copper pipes.

Completed annual heating system maintenance on a gas furnace, inspecting all components and verifying proper operation. Observed clean blue flame pattern during combustion test, indicating efficient operation with no signs of incomplete combustion or safety concerns. System is operating within manufacturer specifications with no issues requiring additional service at this time.

Responded to service call regarding kitchen sink leaking at drain connection. Upon inspection, identified water leakage from the P-trap assembly beneath the sink. Replaced faulty P-trap components and verified proper drainage with no leaks after repair.

Performed comprehensive furnace tune-up and diagnostic testing, with combustion analysis showing normal O2 levels at 11.4%, minimal CO presence, and CO2 at 5.4% with system temperature at 94.1°F. Inspected humidifier and verified customer has appropriate filters on hand.

Performed scheduled maintenance tune-up on 3-year-old furnace. Inspected interior components including fan assembly and air handler, confirming all parts are clean, intact and functioning properly. System is operating within normal parameters with no issues detected.

Responded to main water line leak emergency requiring city water shut-off. Installed new copper pipe fittings at the source of the leak, replacing damaged section with proper elbow joint and securing to framing with pipe support brackets. Confirmed repair was successful with no moisture ingress after service completion.

Performed estimate for furnace and air conditioner replacement of aging equipment. Inspected existing HVAC system, including copper line sets, ductwork, and electrical connections. Evaluated electrical panel capacity to ensure compatibility with potential new system requirements.

Performed inspection on 13-year-old York furnace after buyer's inspection noted gas odor near regulator in upper cabinet. Located and repaired significant corrosion and rust at gas line connection point. System now operating safely with no gas leaks detected.

Performed routine maintenance on Heatmaker furnace system located in basement utility area. Conducted comprehensive inspection of belt-driven unit, checking flame pattern and internal components for proper operation. System is functioning correctly with no immediate issues identified; customer advised about maintenance plan renewal options.

Diagnosed and repaired leaking Bradford White tanked water heater in 50-year-old residential property. Identified leak source at bottom connection point, replaced deteriorated fittings and installed new expansion tank to prevent future pressure issues. Confirmed proper venting of exhaust system and verified all connections were secure with no further leakage detected during testing.

Performed furnace tune-up maintenance service. Inspected flame pattern through sight glass, confirming proper combustion with characteristic blue flame. System is operating normally with no issues detected.

Diagnosed non-operational humidifier system and identified severely clogged evaporator coil as primary cause of poor indoor air quality and system inefficiency. Performed thorough cleaning of evaporator coil to remove extensive dirt buildup and debris accumulation, restoring proper airflow and humidity control capabilities. Recommended regular maintenance schedule to prevent future IAQ issues and extend equipment lifespan.

Performed routine furnace tune-up, inspecting gas burner assembly which showed proper blue flame ignition and combustion. Examined heat exchanger, blower motor, and electrical connections which were all functioning within specifications. System is operating efficiently with no issues detected.

Performed inspection on recently installed Bryant condenser unit damaged by falling ice from roof. Documentation of visible damage to exterior cabinet, fan assembly, and refrigerant lines was completed with photographic evidence. Recommended full replacement of condenser under warranty due to extensive impact damage affecting operational integrity of the system.

Performed preventative maintenance on 12-year-old gas furnace. Completed deliming and descaling service on tankless water heater system. Inspected plumbing connections and drainage system components, noting proper installation of flexible braided supply lines and pump assembly.

Performed scheduled maintenance on Rheem water heater system, including a complete tankless flush to remove mineral buildup. Inspected all copper pipes, valves, and connections for proper function and signs of wear. Replaced air filter to maintain optimal system performance and efficiency.