HVAC & Plumbing Services in Shaker Heights

Responded to no cooling complaint on one-year-old Carrier central air conditioning system affecting entire residence. Upon arrival, performed comprehensive system diagnostics including refrigerant charge verification, electrical component testing, and airflow assessment at both indoor air handler and outdoor condensing unit. Documented equipment conditions with photographs showing Carrier furnace with evaporator coil installation in basement mechanical room, noting clean installation with proper clearances and accessible service access points. Completed diagnostic evaluation and identified root cause of cooling failure, restoring system to proper operation with normal temperature differential and adequate airflow throughout residence.

Completed routine maintenance and tune-up on a 10-year-old residential air conditioning system. Performed comprehensive inspection of all system components, checked refrigerant levels, cleaned condenser coils, inspected return air grille and ductwork, verified proper airflow through horizontal louver vents, and confirmed system operation. No deficiencies identified and unit operating within normal parameters per manufacturer specifications.

Provided estimate for replacement of existing Unico air conditioning system. Current system operational but experiencing refrigerant leak from evaporator coil. Assessed basement installation including furnace, ductwork configuration, and existing high-velocity AC components to determine replacement specifications and scope of work.

Responded to service call for attic-mounted air handler with reported evaporator coil leak. Upon inspection, confirmed active leak at evaporator coil with condensate accumulating in drain pan requiring frequent manual emptying. Assessed condensate drainage system including primary drain pan, overflow safety switch, and condensate pump assembly. Documented existing conditions with photographs showing drain pan configuration, PVC drain lines, and condensate pump installation for further evaluation and repair planning.

Responded to no cooling complaint on residential air conditioning system. Upon arrival, confirmed compressor was not operating and thermostat batteries had already been replaced by homeowner without resolving issue. Performed comprehensive diagnostic testing using digital multimeter to assess electrical components and system functionality. Identified failed capacitor preventing compressor from starting. Replaced defective dual run capacitor with properly rated OEM replacement part. Verified proper voltage and amperage readings across all electrical connections. Tested system operation through complete cooling cycle, confirming compressor engagement and proper refrigerant pressures. System restored to normal cooling operation with all components functioning within manufacturer specifications.

Completed estimate for full HVAC system replacement of approximately 20-year-old equipment. Assessed existing outdoor condenser unit with louvered venting and attic-mounted Luxaire air handler with associated ductwork, condensate drainage system, and auxiliary pump. Documented current system configuration including flexible metallic ductwork, PVC condensate lines, and electrical disconnect for replacement specifications.

Removed and temporarily relocated concrete pavers in herringbone pattern to expose existing underground gas line path. Excavated and removed old gas line from interior of home through existing penetration near glass block window. Installed new grill stand and secured to ground with appropriate anchoring medium. Ran new underground gas line through original path, connecting from interior source point to new grill location. Assembled and installed outdoor grill unit, connected to new gas supply line, and performed complete leak test to verify system integrity and safe operation. Backfilled excavated areas, re-graded as necessary to ensure proper drainage around black corrugated conduit, and reset pavers over completed gas line installation with minimum 5-6 inch depth allowance for sand base and paver thickness.

Responded to no-cooling call on 4-year-old Bryant central air conditioning system experiencing intermittent Error 82 codes and complete system failure. Upon arrival, performed diagnostic testing using refrigerant manifold and micron gauge at the condenser unit to assess system pressures, temperatures, and refrigerant charge levels. Identified the root cause of the error code and system shutdown, completed necessary repairs to restore proper operation, and verified all temperature and pressure readings returned to normal operating parameters.

Completed comprehensive tune-up on a 10+ year old air conditioning system with no reported issues. Performed full system inspection, cleaned outdoor unit condenser coil, checked refrigerant pressures and levels using manifold gauges confirming proper charge, tested electrical components, and verified overall system operation. Unit is functioning within normal parameters and ready for continued service.

Conducted comprehensive HVAC replacement estimate for existing York outdoor condensing unit. Evaluated current system condition, noting standard installation on concrete pad with proper electrical disconnect and adequate clearance from structure. Assessed interior ductwork in basement area, identifying significant condensation issues on flexible metallic supply duct indicating potential insulation deficiency or excessive temperature differential. Documented equipment specifications, installation configuration, and existing ductwork conditions. Provided replacement recommendations addressing both exterior unit upgrade and interior moisture control improvements to ensure optimal system performance and efficiency.

Completed estimate for replacement of 16-year-old residential air conditioning system experiencing no-cool condition. Evaluated existing outdoor condensing unit positioned on concrete pad adjacent to brick exterior and indoor air handler/furnace system located in basement utility area. Documented current equipment configuration including electrical disconnects, refrigerant lines, condensate drainage, and ductwork transitions to provide comprehensive replacement proposal addressing failed cooling capacity.

Completed preventative maintenance tune-ups on two Unico air conditioning systems. Performed standard maintenance procedures including refrigerant pressure and temperature measurements using digital manifold gauges, verified R410A refrigerant charge levels, and conducted system performance diagnostics to ensure optimal operation of both units.

Performed complete AC tune-up on 1-year-old air handler system. Conducted comprehensive system diagnostics using digital gauges to measure refrigerant pressures, temperatures, and superheat readings, confirming proper system operation at 70.2°F ambient conditions. Discussed equipment cover options and ordering process with customer per their request.

Performed scheduled tune-up maintenance on two residential air conditioning systems (5-year-old and 20-year-old units). Conducted comprehensive system diagnostics using refrigerant manifold gauges to verify proper refrigerant pressures and temperatures for R410A refrigerant. Measured operating pressures on both high and low sides, confirmed superheat and subcooling values within manufacturer specifications. Inspected condenser coils, verified proper airflow through heat exchanger fins, and confirmed both systems operating at optimal efficiency with no deficiencies noted.

Responded to no cooling complaint on 3-year-old AC unit that had compressor replacement completed two months prior. Upon inspection, discovered significant contamination in condensing unit base with pooled liquid, debris, and biological growth around compressor and refrigerant lines. System evaluation revealed potential secondary failure or contamination-related issue affecting cooling performance. Documented equipment condition with photos showing deteriorated base pan, moisture accumulation, and compromised cleanliness of critical components requiring further diagnostic assessment to determine root cause of recurring cooling failure.

Completed full HVAC system replacement including removal of existing equipment and installation of new furnace, evaporator coil, air conditioning condenser unit, and Ecobee smart thermostat. All components were properly sized, connected to existing ductwork, and tested for optimal performance with system temperatures verified at 129°F on heating cycle. New installation meets current code requirements and manufacturer specifications.

Replaced deteriorated cast iron and galvanized tub drain line on second floor, including installation of new p-trap assembly. Accessed drain system by opening kitchen ceiling below to expose and remove old piping, then opened wall section where drain line drops to main stack for complete replacement. All new drainage components installed to code with proper venting and secure connections restored.

Completed routine cooling maintenance visit on approximately 10-year-old air handler unit located in attic. Performed standard system inspection, measured operating temperatures using calibrated digital thermometer, and verified proper equipment function during early morning service window.

Performed comprehensive AC tune-up on 5-year-old cooling system with no reported issues. Conducted system diagnostics using digital thermometer and refrigerant manifold gauges, verifying temperature differentials, refrigerant pressures, and overall system performance at the condenser unit. All measurements fell within normal operating parameters, confirming system is functioning properly and ready for continued seasonal operation.

# HVAC Maintenance Service Completed Performed comprehensive air conditioning maintenance on a 3-year-old Carrier CVPVF series unit utilizing R-410A Puron refrigerant. Conducted full system inspection including verification of refrigerant levels, electrical connections, and operational parameters. Provided customer education on proper thermostat programming and operation to optimize system efficiency and comfort control.