HVAC & Plumbing Services in Shaker Heights

Performed routine AC tune-up on residential system. Inspected blower motor and fan assembly, confirmed proper operation. Checked refrigerant pressures using manifold gauges, recorded readings within manufacturer specifications. System operating normally with no issues found during maintenance inspection.

Replaced deteriorated cast iron plumbing stack with PVC piping to resolve water damage visible on ceiling and wall surfaces. The new PVC stack installation eliminated the source of moisture intrusion and restored proper drainage function to the system.

Conducted site assessment for upcoming kitchen faucet replacement on commercial-grade stainless steel double-basin sink. Confirmed existing wall-mounted faucet configuration with two-handle setup and spray attachment requires replacement with customer-supplied fixture compatible with current three-hole mounting arrangement. Documented existing plumbing setup and verified sink compatibility for future installation appointment once new faucet unit is available on-site.

Completed routine AC tune-up on ten-year-old exterior condensing unit. Performed standard maintenance including inspection of electrical connections, refrigerant levels, and operational testing. Identified cracked PVC ventilation pipe at exterior foundation with visible weathering and rust staining at joints; documented condition with photos and advised customer of recommended repair to prevent further deterioration and potential system efficiency issues.

Completed Stage 2 of Bryant furnace installation in basement mechanical room. Performed system diagnostics and commissioning checks using digital multimeter, verifying proper electrical readings at 150 on multiple test points. Confirmed all gas piping connections, flue venting with proper elbow configuration, and clearances around unit meet code requirements. System tested and operational with water heater integration verified.

Conducted comprehensive assessment of existing HVAC system for equipment replacement estimate. Air conditioning unit failing to maintain adequate cooling capacity during operation. Boiler system inspection revealed corrosion on components and piping, indicating deterioration that compromises system integrity and efficiency. Documented existing equipment conditions including Honeywell Vaporstat steam pressure control, corroded piping at base of mechanical equipment, and condensate drain lines showing age-related wear. Photographed current system configuration and equipment deficiencies to support replacement recommendations for both heating and cooling systems.

Responded to service call for inadequate airflow and poor ventilation distribution to certain rooms throughout the residence. Upon inspection, accessed the blower assembly and examined the squirrel cage fan wheel for debris accumulation, blade damage, and proper rotation. Found the blower wheel and housing required cleaning due to dust and debris buildup restricting airflow capacity. Inspected ductwork system in basement area, noting proper installation of insulated supply runs. Verified all mechanical components of the HVAC system were functioning within normal parameters. System airflow restored to proper circulation levels with improved ventilation distribution to all affected rooms.

Completed scheduled maintenance on a 10-year-old mini split system that was previously deferred due to cold weather conditions. Performed comprehensive cooling system inspection, cleaned indoor and outdoor units, checked refrigerant levels, tested electrical connections, and verified proper operation of all components. System is operating within manufacturer specifications and ready for the cooling season.

Completed warranty compressor replacement on HVAC unit as required second service call. Disconnected and replaced electrical connectors to compressor, ensuring proper wire routing and secure connections between system wiring harnesses. All electrical connections tested and verified operational upon startup.

Responded to no hot water complaint at residential property. Upon inspection, diagnosed failed water heater in 23-year-old home. Unit had reached end of serviceable life and was no longer producing hot water for household fixtures including showers and faucets. Documented existing installation conditions showing standard tanked water heater with copper supply lines, PVC venting, and proper mounting in utility closet. Photographed equipment and plumbing configuration for service records.

Completed free estimate for water heater replacement in residential basement utility area. Assessed existing white cylindrical tanked water heater installation with connected expansion tank, copper supply lines, PVC venting system, and associated plumbing components. Documented current system configuration including AMTROL expansion tank mounted to ceiling joists, pressure relief valve, and existing piping layout. Provided recommendations for complete water heater replacement at scheduled 8am appointment.

Completed scheduled maintenance on a 6-year-old air conditioning system located in attic space. Performed comprehensive inspection of air handler unit, verified all manufacturer labels and specifications were intact, and examined evaporator coil assembly which showed normal dust accumulation consistent with operational use. All components found in satisfactory working condition with no immediate service needs identified.

Completed routine air conditioning maintenance on a three-year-old system that was operating properly at time of service. Used digital manifold gauges to measure and verify refrigerant pressures and temperatures at the evaporator coil, confirming system performance within manufacturer specifications. All standard tune-up procedures were performed to ensure continued efficient operation.

Responded to service call for air handler that was not activating. Unit had been previously turned off per homeowner request but was switched back on during January visit and subsequently failed to operate. Restored power to air handler and verified proper system operation to return HVAC system to full functionality.

Responded to emergency call for leaking pipe in century-old residential property. Upon arrival, identified active water leak in exposed plumbing system located in basement area near ceiling joists. Documented extensive water damage including brown staining on walls and ceiling surfaces, with visible moisture intrusion through access panel opening. Coordinated with property owner regarding municipal water company shut-off requirements prior to commencing repairs. Assessed aging pipe infrastructure running along upper wall and ceiling sections in finished basement living space. Photographed damage extent and leak source for documentation purposes. Repair work required 5-hour estimated completion time pending water service shut-off coordination.

Responded to report of suspected plumbing leak in century-old home with significantly elevated water consumption. Performed diagnostic inspection of second floor and basement toilet systems to identify source of water loss. Upon examination of toilet tank, discovered extensive mineral deposits, rust staining, and corroded internal components consistent with prolonged water seepage. Low water level in tank and deteriorated flapper valve assembly indicated continuous water flow into bowl. Documented condition of flush valve mechanism, float assembly, and tank interior showing advanced corrosion and sediment accumulation affecting proper seal function. Identified failing flapper as primary cause of water waste, resulting in constant running toilet condition that would account for dramatic increase in monthly water usage.

Responded to service call for air conditioning system not operating properly, affecting entire home. Upon arrival, performed comprehensive system inspection of less than one-year-old unit. Examined outdoor condensing unit, verifying proper installation on concrete pad with adequate drainage configuration via PVC condensate lines and P-trap assembly. Inspected indoor components including refrigerant line sets with foam insulation and associated ductwork connections. Conducted operational testing of system components, checked refrigerant pressures, verified electrical connections, and assessed airflow throughout system. Documented equipment condition with photographs for service records. System restored to proper working order and homeowner advised of findings.

Completed preventive maintenance tune-up on two 20-year-old outdoor air conditioning systems. Inspected both units, including electrical components, capacitors showing weathering and corrosion, wiring connections, and condensing units mounted on concrete pads. Performed standard maintenance procedures, documented equipment condition with photos, and verified both systems operational upon completion.

Completed comprehensive maintenance tune-up on 4-year-old outdoor air conditioning unit located on exterior concrete pad against brick wall. Performed full system inspection including refrigerant levels, electrical connections, condenser coil cleaning, and operational testing during high ambient temperature conditions (91°F). All components found operating within manufacturer specifications with no deficiencies noted.

Serviced and evaluated three Hansgrohe faucet fixtures in residential shower installation. Inspected handheld shower system with chrome-finished slide bar assembly, adjustable bracket mechanism, and flexible hose connection, ensuring proper mounting bracket security and operational functionality. Confirmed brand compatibility and completed necessary repairs to restore fixtures to proper working condition.