HVAC & Plumbing Services in Shaker Heights

Responded to no-heat call on furnace system where A/C was operational but heating function had failed. Performed diagnostic troubleshooting on electrical components and control board connections, inspecting wiring harnesses, motor assemblies, and PCB connections within the unit. Identified and addressed the issue preventing furnace operation, restoring heat functionality to the system.

Responded to service call for 3-year-old air handler not cooling properly. Upon inspection, found evaporator coil frozen and measured supply air temperature at 85°F, confirming inadequate cooling performance. Advised customer that system requires time to fully thaw before proper diagnosis can be completed, and scheduled follow-up appointment to determine root cause of freezing condition once coil has defrosted.

Responded to service call for Bryant condenser unit with main compressor failure to start. Upon arrival, found outdoor unit heavily clogged with accumulated dirt, dust, and debris on cooling coils and fins, with vegetation growth around base impeding proper airflow. Performed diagnostic testing on compressor and electrical components. Thoroughly cleaned condenser coils and fins to remove substantial buildup that was restricting heat exchange capacity. Cleared vegetation from around unit perimeter to restore adequate clearance for proper operation. Tested system operation following cleaning and verified compressor startup and normal function. Unit returned to full operational status with improved airflow and cooling efficiency.

Performed on-site assessment of reported leaking pipe associated with existing tank-style water heater in basement utility area. Documented current plumbing configuration including copper supply lines, shut-off valves, and connections to determine source of leak and provided estimate for repair options including conventional water heater replacement or tankless system installation.

Completed gas line rerouting in basement utility area to accommodate updated mechanical system configuration. Work involved relocating existing gas piping away from water heater and HVAC components, installing new copper gas lines with proper fittings and connections, and ensuring all installations met code requirements for clearances and safety. All connections were pressure tested and verified for proper operation.

Performed annual maintenance and tune-up on 10-year-old boiler system. Conducted combustion analysis revealing carbon monoxide levels at 14 ppm and flue gas temperature of 20.6°C, indicating proper combustion efficiency. Inspected heat exchanger and identified moderate corrosion and oxidation on vertical tubes and aluminum fins, with visible rust discoloration and mineral deposits present throughout the assembly. Cleaned burner components, verified proper operation of all safety controls, and confirmed system is functioning within acceptable parameters for continued service.

# Moen Flo Smart Water Monitor Installation Completed installation of Moen Flo whole house smart water monitoring system on residential plumbing distribution panel. Integrated dual electronic monitoring devices into existing copper supply line configuration with brass fittings and pressure regulation components. Installed system pressure gauge for real-time monitoring capability, configured electronic sensors with proper wiring connections, and verified all connections for leak-free operation. Mounted installation documentation and spare components packet on service panel. System tested and operational, providing automated water flow monitoring and leak detection functionality for the entire household plumbing system.

Completed comprehensive cooling system tune-up on 5-year-old air handler unit. Connected Testo 550 digital manifold gauges to measure system performance, recording subcooling at 17.5°F and superheat at 10.7°F, indicating proper refrigerant charge and system operation. All measured parameters within manufacturer specifications for optimal cooling efficiency.

Completed scheduled cooling system preventive maintenance on residential split system air conditioning unit. Performed comprehensive tune-up including inspection of outdoor condensing unit, verification of refrigerant line integrity, assessment of electrical connections, and evaluation of overall system operation to ensure optimal performance for the cooling season.

Completed installation of New Yorker steam boiler model CGS60C with all associated components including automatic water feeder, low water cutoff, sight glass, pressure control, and programmable thermostat. Installed new backflow preventer and modified all near boiler piping to meet current specifications. Ran dedicated electrical circuit to panel and terminated connections for boiler operation. Corrected pitch on radiator supply piping to resolve heating issue in bedroom, ensuring proper steam flow and condensate return.

Found the system low on refrigerant and added UV dye along with refrigerant to bring the system back to proper charge. A follow-up visit is scheduled in 1-1.5 weeks to locate the leak using the UV dye under black light inspection.

Responded to service call for reported boiler leak at 104-year-old residential property. Upon arrival, conducted thorough inspection of heating system and plumbing infrastructure in basement utility area. Examination revealed the concern was related to the water heater rather than the boiler system. Inspected white cylindrical water heater unit and found significant water staining and mineral deposits on top surface of tank, indicating previous moisture issues. Left copper pipe connection showed advanced corrosion and oxidation with reddish-brown discoloration at base fitting, suggesting long-term exposure to moisture. Pressure relief valve assembly on right side examined and found to be intact with proper metallic discharge piping in place. Traced copper supply lines along wall and ceiling joists to identify potential leak sources. Tagged affected piping section for reference and documentation. Noted varying conditions of copper piping throughout system, with some sections showing

Performed comprehensive AC tune-up on Carrier outdoor condensing unit. Inspected all major components including compressor, condenser coil, fan motor, and electrical connections. Verified proper refrigerant pressures and system operation. Condenser coil showed moderate accumulation of debris between fins; cleaned coil to restore optimal airflow and heat transfer efficiency. Checked recently replaced capacitor for proper operation and secure mounting. Cleared vegetation growth from base of unit and around concrete pad to maintain adequate clearance. Tested system startup and shutdown sequences, confirmed proper amperage draw on all components. System operating within manufacturer specifications with no issues detected.

Responded to no cooling complaint on 3-year-old air conditioning system previously installed by our company. Upon arrival, inspected indoor HVAC equipment including furnace and air handler in basement utility area. Verified system operation, checked electrical connections, and documented equipment condition with photos showing proper installation and ductwork connections.

Completed routine air conditioning tune-up on residential outdoor condensing unit. Performed standard maintenance inspection, checked refrigerant levels, cleaned condenser coils, verified electrical connections, and tested system operation to ensure optimal cooling performance for the season.

Responded to water leak originating from third-floor shower fixture with water penetrating through multiple floors to basement level. Upon arrival, inspected the identified shower faucet and associated plumbing connections. Examined vintage plumbing system consistent with the 111-year-old structure, including aged chrome drain pipes, flexible braided supply lines, and wall-mounted fixtures showing significant weathering and tarnish. Assessed the extent of water intrusion pathway from third floor through building envelope to basement. Isolated the leak source at the shower valve assembly and verified no additional leak points in adjacent bathroom fixtures or supply lines. Documented existing plumbing conditions including traditional pedestal sink connections and period-appropriate tile work. Completed necessary repairs to eliminate active water flow and restore proper fixture operation, preventing further water damage to lower levels.

Completed drain line repair for sink by exposing and accessing concealed plumbing within ceiling cavity. Opened ceiling to locate and assess deteriorated drain pipe, removed damaged section, and installed new drain line with proper fittings and secure connections. Restored proper drainage function and ensured all connections were leak-free and code-compliant.

Leveled Bryant condenser unit to manufacturer specifications to prevent compressor damage and oil migration issues. Unit was found to be improperly positioned on pad, creating potential for premature equipment failure. Adjusted and stabilized condenser on concrete pad using proper leveling techniques, verified alignment with precision level tool to ensure optimal refrigerant flow and compressor longevity.

Installed ductless mini-split system to provide heating and cooling for room above garage. Mounted outdoor condenser unit on pad against exterior brick wall with proper clearances and installed indoor air handler unit high on interior wall near ceiling corner. Ran refrigerant line set through wall between units with white line set cover for protection and finished appearance, completed all electrical connections, tested system operation, and verified proper functionality of all components including temperature controls and airflow distribution.

Removed and reset toilet after replacing defective PVC tee and toilet bend in the drainage system. Installed a 4-inch Gripper expanding plug in an existing floor drain. Rerouted approximately 20 feet of condensate drainage line from the basement furnace to a properly trapped floor drain, ensuring compliance with plumbing codes and proper system function.