HVAC & Plumbing Services in Cleveland Heights, OH

Completed comprehensive kitchen and bathroom sink repiping project, requiring removal of wall access panels to replace deteriorated supply and drainage components. Successfully installed new PVC drain lines and copper supply piping throughout both locations, addressing visible water damage in the utility area ceiling and ensuring proper connections to existing plumbing infrastructure.

Responded to a no heat call for a York furnace under 10 years old. Diagnostic inspection revealed significant corrosion on the control board with damaged wiring connections. Replaced control board assembly, tested system operation through multiple heating cycles, and verified proper airflow throughout the home. System now functioning within manufacturer specifications.

Performed routine maintenance on 12-year-old boiler system. Inspected burner assembly and confirmed proper flame pattern with consistent blue flames across all ports. Examined heat exchanger which showed normal wear with some surface oxidation and minor mineral deposits, but remains functionally sound without any safety concerns.

Performed scheduled maintenance on 10-year-old steam boiler system. Identified significant corrosion on heat exchanger components and venting, with extensive rust development on metal surfaces. Documented deteriorating seals at wall/vent junction requiring attention during next service visit.

Conducted inspection of mini split system and boiler installation to address improper venting configuration. Identified that boiler exhaust is currently venting directly onto mini split units, causing them to ice over. Documented existing utility infrastructure in basement mechanical area to prepare comprehensive estimate for proper ventilation system modification.

Performed scheduled heating system tune-up and conducted comprehensive diagnostic testing with UEi analyzer to verify proper combustion parameters. Inspected PVC venting system for secure connections and proper installation. Confirmed normal blue flame pattern in burner assembly, indicating efficient operation with no combustion issues detected.

Completed scheduled heating tune-up service on a residential HVAC system. Performed temperature differential testing with readings of 123.4°C at supply register and conducted static pressure measurements using HT-1890 manometer with readings of 35.2. All system parameters verified within operational specifications.

Completed annual inspection on boiler heating system. Inspected heat exchanger fins for dust accumulation and checked burner assembly for proper flame pattern and color. System operating with normal blue flame signature; cleaned minor dust buildup from heat exchanger fins to ensure optimal thermal transfer.

Performed scheduled boiler maintenance service including full system inspection and combustion analysis using C161 Combustion Analyzer. Verified proper O2 levels (21.0%), confirmed zero CO emissions, and documented normal operating temperatures (103.0°F). Heat exchanger surfaces showed normal condition with no signs of deterioration.

Performed comprehensive furnace tune-up on Lennox HVAC system. Inspected and cleaned blower assembly components, removing accumulated dust from fan blades and housing. Verified proper operation of all mechanical components and ductwork connections to ensure optimal airflow and system efficiency.

Responded to service call for boiler with PCB natural cycling issues causing shutdowns requiring manual restart. Inspected system following previous service visits by Paul and Jeff. Observed fluorescent tubes/ignition assembly during diagnostic testing and identified potential control board malfunction causing the intermittent operation.

Performed comprehensive tune-up service on customer's steam boiler system. Inspected water level sight glass, safety valves, and main control valves for proper operation. Examined Lennox furnace unit and associated ductwork, ensuring all components were functioning correctly and safely.

Performed scheduled heating maintenance on two systems. Conducted combustion analysis using UEi C161 analyzer, confirming proper oxygen levels (21.0%), zero carbon monoxide, and operational temperature (117.5°F). Inspected evaporator coil condition, noting standard fin alignment with no visible damage or excessive buildup.

Performed scheduled maintenance on hydronic boiler system that had been previously rescheduled. Inspected ventilation components which showed significant dust accumulation requiring cleaning. Checked system pressure gauge which was operating within normal parameters on the copper supply/return piping.

Responded to no heat call for 10-year-old natural gas boiler. Diagnostic inspection revealed faulty pressure gauge reading zero. Replaced pressure gauge, bled air from system, and restored proper system pressure. Heat function verified operational before departure.

Performed comprehensive heating tune-up on furnace system. Inspected burner assembly confirming proper ignition with clean blue flames across all elements. Conducted diagnostic testing with electronic analyzer to verify system parameters within manufacturer specifications.

Successfully installed new steam gas boiler with dual 2" risers connecting to existing 3" header as specified in installation manual. Replaced two main steam vents and installed new backflow preventer and automatic water feeder while preserving the existing vaporstat and thermostat. All connections properly secured and system tested for optimal performance.

Performed annual heating tune-up under Home Plan maintenance agreement. Conducted full combustion analysis with readings of O2: 6.7%, CO: 4P, CO2: 8.1%, and flue temperature: 102.5°F. Observed significant corrosion on heat exchanger components that will require monitoring at next service visit.

Performed scheduled maintenance on furnace. Conducted combustion analysis which showed normal readings (O2 7.4%, CO2 7.7%, T1 495.5F, CO 0ppm). Visual inspection of heat exchanger revealed normal oxidation and dust accumulation consistent with regular operation.

Performed routine furnace maintenance service including combustion analysis, which showed normal O2 (12.7%), CO2 (4.7%), and zero CO emissions. Inspected burner assembly and control wiring connections for proper operation.