HVAC & Plumbing Services in Cleveland Heights, OH

Conducted site assessment of Reznor heater in basement area with significant ceiling damage and deterioration. Identified Lennox HVAC system and adjacent water heater with visible corrosion and aging components. Documented extensive structural issues including exposed joists, crumbling ceiling material, and compromised mechanical installation area requiring full replacement options.

Responded to no heat call for system under 10 years old. Performed pressure testing with manometer (reading 1.55) and temperature diagnostics (ambient reading 63.2°F). Restored heating functionality by adjusting gas pressure to manufacturer specifications and verified proper operation before completion.

Performed scheduled maintenance inspection on boiler system. Examined heat exchanger components for dust accumulation and conducted visual inspection of gas burner assembly. Verified proper flame characteristics and combustion operation with all four burners functioning normally.

Performed scheduled heating system maintenance. Conducted combustion analysis with UEi C161 analyzer showing normal CO2 (7.4%) and O2 (8.0%) levels at 104.5°F. Temperature probe readings (57.6°) confirmed system operating within parameters.

Performed comprehensive heating system maintenance check including combustion analysis with readings of 21.0% O2, 0.0% CO2, and system temperature of 133.9°F. Inspected blower wheel assembly for proper operation and cleanliness, noting minimal dust accumulation on fan blades. Renewed TechFurn maintenance agreement for continued system coverage.

Performed scheduled maintenance on a 30-year-old MVP boiler under the Home plan plus agreement. Inspected water level gauge, control systems, and copper piping connections. Confirmed proper operation of Honeywell control box and examined brass fittings for leaks or signs of deterioration.

Performed comprehensive boiler tune-up as part of the BOGO MVP service plan renewal. Conducted combustion analysis with readings of CO2 at 0.08% and supply air temperature at 84.6°F. Inspected burner assembly and electrical connections, confirming proper operation of all components.

Replaced failed cold water supply line to kitchen. Installed new copper piping with brass fittings and blue-handled shutoff valves along basement joists. System was pressure tested and confirmed operational with no leaks.

Performed diagnostic inspection on gas-fired tanked water heater in century home. Examined burner assembly, confirming proper flame pattern and combustion (blue flames visible). System functioning normally with no operational issues detected; no repairs required at this time.

Performed routine maintenance on 10+ year old hydronic boiler. Conducted combustion analysis with digital analyzer showing O2 levels at 21.0% initially and CO2 at 7.1% post-adjustment, with flue gas temperature reaching 409.1°F. System now operating within manufacturer specifications.

Conducted inspection of aging tanked water heater system with significant corrosion and deterioration evident throughout the installation. Assessment revealed a Reznor unit with extensive rust damage to the lower section, compromised copper components, and potential ventilation issues. Recommended replacement of the 30-gallon water heater due to end-of-life condition and safety concerns.

Inspected mini-split system with reported leak; confirmed refrigerant leak along wall with visible condensation damage. Accessed internal components of wall-mounted indoor unit for diagnostic evaluation; system requires refrigerant recharge and leak repair to restore proper operation.

Responded to service call for gas fireplace not receiving gas. Performed pressure test on previously installed gas line to verify integrity. Restored gas flow to fireplace and confirmed proper operation with visible flame pattern across decorative glass media. Fireplace is now functioning correctly with no leaks detected in the supply line.

Performed scheduled heating tune-up on residential furnace system. Inspected burner assembly operation, confirming proper flame characteristics with consistent blue flames across all tubes. Noted dust accumulation on heat exchanger fins requiring cleaning to optimize system efficiency and heating performance.

Completed relocation of gas and water supply lines in kitchen area to accommodate customer's remodeling project involving refrigerator and stove repositioning. Accessed utility space to properly route yellow gas line and metal water pipes through the crawlspace. Performed pressure test on completed gas line installation to verify system integrity and ensure no leaks were present.

Responded to service call for shower leakage issues in century-old home. Upon inspection, identified water seepage around the diverter plate and shower head connection. Replaced worn gaskets and applied appropriate sealant to create proper waterproof barrier at fixture-to-wall interfaces, successfully resolving the leak condition.

Performed standard furnace tune-up on residential system located in basement. Inspected and replaced dirty air filter. Addressed squeaking noise from furnace by lubricating blower motor bearings and checking belt tension. System now operating within normal parameters with noise issue resolved.

Completed full HVAC system replacement including installation of new Bryant condenser unit, furnace, evaporator coil, and thermostat. Relocated furnace venting to front of home and reconfigured return air system by removing secondary return. Preserved existing humidifier and filter as requested by customer.

Performed comprehensive maintenance service on 20+ year old boiler system. Inspected electrical connections, heat exchanger, and venting system for proper operation. Noted aging equipment with standard wear; system is operational but customer should consider replacement options in the near future due to equipment age.

Performed warranty service call to replace defective control board in commercial HVAC system. Installed new PCB module, reconnected all electrical components, and verified proper system operation after replacement. Unit now functioning within normal parameters.