HVAC & Plumbing Services in Cleveland Heights, OH

Completed installation of Bryant split-system air conditioning system including outdoor condenser unit, attic-mounted air handler, and new ductwork throughout the home. The outdoor condenser was positioned on a pad against the brick exterior with proper clearances maintained, electrical disconnect box installed and labeled for both air handler and condenser circuits, and refrigerant lines run to the attic air handler. All new ductwork was installed in the attic space to provide cooling to the entire second floor, with additional supply runs extended to the first-floor living room and kitchen areas as space permitted. Electrical connections were completed with appropriate circuit protection, and the system was tested for proper operation upon completion.

Performed routine preventive maintenance tune-up on a Trane XR series air conditioning system (Model 4TTR3030H1000NA, manufactured May 2017). Conducted comprehensive inspection of the outdoor condensing unit, verified proper operation of all components, and confirmed system specifications matched nameplate data. No deficiencies were identified during the inspection, and the unit was found to be operating within normal parameters for an 8-9 year old system.

Completed preventive maintenance tune-up on two 4-year-old air conditioning systems. Performed comprehensive inspection of both units including condenser coil cleaning, blower wheel examination, and verification of all mechanical components. All systems operating within manufacturer specifications with no deficiencies noted.

Performed routine maintenance cooling system inspection on a 4-year-old air handler unit. Conducted comprehensive evaluation of indoor air handler components including blower assembly, evaporator coil, and ductwork condition. Inspected outdoor condensing unit mounted on rooftop platform, verifying proper operation of compressor, condenser fan motor, and refrigerant lines. Examined electrical connections at disconnect box and service panel, confirming secure wiring and proper voltage supply. Cleared accumulated debris from around condenser unit base and roof perimeter to ensure adequate airflow and prevent potential drainage issues. System operating within normal parameters with no immediate repairs required at time of service.

Performed annual maintenance on 15-year-old Bryant air conditioning system. Completed standard tune-up procedures including inspection of outdoor condensing unit, verification of refrigerant levels, cleaning of condenser coils, and evaluation of electrical connections and components. Unit operational at time of service completion.

Responded to service call for abnormal water consumption indicated by significant increase in monthly water bill. Performed diagnostic inspection of exterior plumbing system including main water line, irrigation connections, and pressure regulation components. Identified issue with exterior PVC piping assembly and associated valves mounted on building exterior. Inspected filter housing, pressure regulation system, and multiple connection points for signs of leakage or system malfunction that would account for excessive water usage.

Completed comprehensive air conditioning tune-up maintenance service with no reported issues at time of arrival. Performed system diagnostics including temperature differential measurements across the evaporator coil, recording supply air temperature of 63.6°F. Inspected indoor air handler unit, ductwork connections, and insulation integrity to ensure proper system operation and energy efficiency for the cooling season.

Completed annual air conditioning maintenance on a 23-year-old cooling system. Performed comprehensive inspection of the Trane furnace and associated HVAC components, including visual examination of internal wiring, electrical connections, and mechanical components with lower access panel removed for thorough access. Verified proper operation of humidifier/air handler unit and associated control systems. Inspected ductwork installation including black flexible insulated ducts and support systems throughout the mechanical space. Checked PVC condensate drainage system for proper flow and configuration, ensuring all connections and routing were secure and functional. Tested system electrical components using multimeter to verify proper voltage and amperage readings. Confirmed all equipment operating within manufacturer specifications for the cooling season.

Responded to AC unit repair call and performed diagnostic evaluation of residential air conditioning system. Connected Testo 550 digital manifold gauge to outdoor condenser unit and measured refrigerant pressures and temperatures for R410A system. Recorded suction pressure of 20.19 psi with corresponding temperature of 35°F, and discharge pressure of 68.5 psi with temperature of 48°F. Inspected indoor furnace and air handler components in basement, verifying proper ductwork connections and system configuration. Documented system conditions with diagnostic photos for service records. Unit operational following assessment.

Conducted comprehensive assessment of existing furnace system located in unfinished basement area for replacement estimate. Documented current HVAC unit configuration, including vertical furnace installation with multiple branch ductwork connections and return air grille. Evaluated existing ductwork infrastructure, noted exposed metallic distribution system extending across ceiling joists, and assessed flexible duct connections to primary unit. Photographed furnace cabinet with access panel open to document internal burner assembly and control components for replacement specifications. Property was unoccupied at time of inspection, accessed via lockbox per arrangement.

# HVAC Service Report Performed annual air conditioning maintenance on an 18-year-old system. Conducted comprehensive diagnostics using digital manifold gauges to measure refrigerant pressures and temperatures, confirming R-22 refrigerant levels and system performance. All testing indicated the unit is operating within acceptable parameters for its age, and no immediate repairs were required at this time.

Completed annual cooling system maintenance on a 7-year-old residential air conditioning system. Performed comprehensive tune-up including inspection of outdoor condenser unit and indoor furnace/air handler, cleared vegetation growth from condenser louvers to restore proper airflow, verified all electrical connections, tested system operation, and confirmed equipment is functioning within normal parameters for the cooling season.

Completed full air conditioning system installation in residential property. Installed new outdoor condensing unit on concrete pad with new electrical disconnect box. Ran new copper refrigerant line set from outdoor unit to indoor air handler, properly insulated and secured. Mounted new Ecobee smart thermostat with remote sensor for zone temperature monitoring and programmed system settings. Installed condensate pump with PVC drainage piping to handle air handler condensate removal. Made all electrical connections, evacuated and charged refrigerant system to manufacturer specifications, and verified proper system operation including airflow, temperature differential, and thermostat communication.

Responded to emergency call for gas leak detected by gas company near recently installed Bradford White water heater. Upon arrival, gas supply was already shut off for safety. Conducted thorough pressure test on all gas lines and connections associated with the water heater installation. Inspected copper piping, brass fittings, and compression connections at top of unit for leaks using soap bubble solution and pressure testing equipment. Verified all connections at the gas control valve and burner assembly. Identified and repaired faulty connection point causing gas leak. Re-tested entire system to confirm leak was eliminated and all connections achieved proper seal. Restored gas supply and verified water heater ignition and proper operation. System tested and confirmed safe for continued use.

Completed comprehensive cooling maintenance on two air conditioning systems per annual Home Plan agreement. Performed full system inspections including blower assembly evaluation, airflow verification, and refrigerant pressure/temperature analysis using digital manifold gauges. Both units operating within manufacturer specifications with proper superheat and subcooling values confirmed.

Completed routine maintenance and tune-up on dual-system HVAC installation consisting of basement furnace and attic furnace unit. Performed comprehensive inspection of both four-year-old furnace systems including burner assembly, heat exchanger, gas connections, electrical components, and venting. Verified proper operation of blower motors, checked air filters, tested safety controls, and confirmed all mechanical and plumbing connections were secure with no leaks detected. Both systems operating within manufacturer specifications with no issues found.

Responded to emergency service call for A/C unit in finished attic space leaking water through ceiling, causing significant structural damage and partial ceiling collapse. Upon inspection, located Carrier HVAC system in attic crawl space and assessed condensate drainage system for blockages or failures. Documented extensive ceiling damage in living area below unit, including compromised decorative plaster and exposed backing material, and photographed equipment installation including furnace unit, ductwork, PVC condensate piping, and condensate pump to identify source of water intrusion.

Performed comprehensive summer tune-up on residential air conditioning system with no reported issues. Connected digital manifold gauges to measure refrigerant pressures and temperatures, verified proper system operation and airflow across condenser coil. All readings within manufacturer specifications, unit operating normally upon completion of preventive maintenance inspection.

Responded to service call for toilet evaluation and replacement quote. Upon arrival, assessed existing standard two-piece white porcelain toilet with raised seat and lid. Customer requested replacement with comfort-height (ADA-compliant) toilet featuring high-flush performance capability. Inspected current installation including water supply line, shut-off valve, floor flange connection, and mounting configuration against subway-tiled wall. Documented existing floor tile pattern and spatial constraints for replacement unit specifications. Photographed current fixture and surrounding area to provide accurate measurements and installation requirements for quote preparation. Provided customer with recommendations for comfort-height toilet models with enhanced flushing systems suitable for their needs.

Performed comprehensive tune-up on 20-year-old Lennox air conditioning system. Conducted complete system diagnostics using manifold gauges to verify refrigerant pressures and temperatures across both the outdoor condensing unit and indoor air handler. All readings were within manufacturer specifications, confirming proper system operation and refrigerant charge. Inspected electrical components, cleaned condenser coils, and verified proper airflow throughout the system. Unit operating efficiently with no deficiencies noted.