HVAC & Plumbing Services in Cleveland Heights, OH

# Service Call - No Cooling and Intermittent Cycling Responded to callback for 11-year-old AC system experiencing no cooling, intermittent cycling, and electrical issues causing light flickering. Performed comprehensive system inspection including UV leak detection and visual examination of air handler, evaporator coil assembly, and associated components. Inspected ductwork, refrigerant lines, condensate pump, and electrical connections. Documented system condition with diagnostic photography to identify root cause of cycling issues and potential electrical load problems affecting household circuits.

Responded to service call for non-operational air handler located in attic space. Upon inspection, diagnosed and resolved the issue with the indoor unit, restoring proper system functionality. Verified outdoor condensing unit and complete system operation before departure.

Completed diagnostic inspection of residential plumbing system to assess requirements for new washer/dryer water line installation and replacement of deteriorated galvanized piping in basement. Documented existing copper supply lines, heavily corroded galvanized vertical stack with extensive rust degradation, and current pipe routing through floor joists and structural framing to provide accurate quote for water line extension to proposed appliance location and full galvanized pipe replacement throughout basement area.

Completed standard water heater flush and fill service on natural gas tanked unit located in basement utility room. Upon arrival, identified active leak from bottom of tank, indicating internal corrosion and tank failure. Documented existing conditions with photographs showing water heater installation, surrounding plumbing connections, expansion tank, and copper supply lines. Due to leak from tank bottom, advised customer that unit requires replacement as this condition is not repairable and poses risk of catastrophic failure.

Replaced chrome tub spout in bathroom of century-old home. Removed existing worn spout and installed new unit, ensuring proper fit and seal to prevent leaks. All connections tested and verified operational upon completion.

Conducted on-site assessment for adding supplemental cooling capacity to upper floors of residence. Evaluated existing Bryant furnace system with humidifier, current ductwork configuration, and available space in mechanical room for potential additional air handler or zone control equipment. Documented existing HVAC infrastructure including plenum connections, condensate drain lines, and electrical service to determine feasibility and requirements for enhanced cooling distribution to upper levels.

Responded to emergency no-cool call for fifteen-year-old central air conditioning system. Arrived on-site to find outdoor condenser unit operational but system failing to provide adequate cooling to the residence. Performed diagnostic evaluation of the unit, which included visual inspection of the condenser, electrical connections, and refrigerant lines to identify the root cause of the cooling failure and restore proper system operation.

Responded to callback for non-operational air conditioning system following two previous service visits. Performed comprehensive diagnostic evaluation of residential HVAC system with fresh assessment approach. Documented equipment condition and installation configuration including furnace unit, ductwork connections, PVC venting system, and electrical components for warranty review and resolution of ongoing cooling failure.

Responded to service call for leaking tanked water heater. Upon inspection, identified a Bradford White Defender Safety System water heater in basement utility area with active water leak. Documented existing installation including copper supply lines, pressure relief valve, and venting system. Assessed unit condition and leak source, then provided customer with repair options and replacement estimate for the aging water heater system.

Conducted comprehensive evaluation of existing HVAC system for replacement estimate. Assessed outdoor condensing unit displaying weathering and dirt accumulation, documented model 3812E18385 with serial number 24HN873G, verified TXV metering device and electrical specifications, confirmed AHRI certification. Inspected indoor furnace installation in basement mechanical room, evaluated vertical furnace unit with PVC venting system, examined adjacent air handling equipment with associated refrigerant lines and shut-off valves. Photographed equipment specifications, installation conditions, and surrounding mechanical space to prepare detailed replacement proposal for complete system upgrade.

Replaced residential water heater storage tank with new unit, including all necessary plumbing connections and proper integration with existing system components. Tested and cycled equipment to verify proper operation and confirm all connections were secure and functioning correctly.

Performed comprehensive tune-up and inspection on two basement boilers—a 60-year-old unit and a 40-year-old unit—both operating normally at time of service. Conducted full system diagnostics including combustion analysis, burner inspection, gas valve operation verification, and safety control testing on both units. Verified proper flame characteristics with blue ignition pattern present, confirmed gas line connections and fittings secure, and inspected electrical wiring and control systems for both boilers. Cleaned burner assemblies, checked for carbon buildup, and ensured proper venting. Inspected one radiator exhibiting rust deterioration and documented condition for follow-up. All safety controls tested and functioning within manufacturer specifications. Both boilers returned to service with normal operating parameters confirmed.

Completed routine annual maintenance on residential 2-year-old air conditioning system. Performed comprehensive inspection of outdoor condenser unit, including examination of coil fins, electrical connections, and refrigerant levels. Unit found to be in good operating condition with all components functioning within manufacturer specifications.

Completed installation of reverse osmosis water treatment system under kitchen sink. Assessed existing plumbing configuration including P-trap, garbage disposal unit, and supply lines to ensure proper integration of RO system with current setup.

Responded to no cooling complaint on third-floor through-the-wall air conditioning unit. Upon arrival, evaluated 40-year-old unit installed in bedroom with sloped ceiling. Inspected unit for operational issues, checked electrical connections, and assessed overall condition of aging equipment. Documented existing installation and unit condition with photographs for service records.

Completed preventive maintenance tune-ups on three split system air conditioning units. Performed comprehensive inspections of outdoor condensing units and attic-mounted air handler, including filter checks, electrical connections, refrigerant levels, and ductwork examination. All systems operational with proper airflow through insulated flex duct distribution network.

Installed a 50-gallon Bradford White water heater to code in basement utility room. Completed all copper piping connections with brass fittings and valves, installed proper ventilation ductwork with metallic flex piping routed across ceiling joists, and connected gas line with shutoff valve. All plumbing connections, venting, and safety components were installed per manufacturer specifications and local code requirements.

Completed furnace replacement estimate for residential property. Assessed existing heating system and fireplace configuration, documented current conditions including brick fireplace construction and floor-level installation requirements. Provided customer with equipment options and installation specifications for new furnace system.

Completed full HVAC system installation including furnace, evaporator coil, air conditioning unit, and thermostat with proper cold air return connections. Performed system commissioning with refrigerant manifold gauge readings confirming proper pressures and temperatures across all circuits, and verified static pressure measurements using differential manometer to ensure optimal airflow and system performance. All equipment tested and operational per manufacturer specifications.

# HVAC Install - Steam Gas Boiler Completed full steam boiler replacement, removing existing unit and installing new Weil McLain EG-65 steam boiler with sidewall power venter kit. Modified venting configuration to eliminate chimney venting in favor of direct sidewall discharge system. Installed new automatic water feeder and backflow preventer to ensure proper system water management and code compliance. Retained existing vaporstat control for steam pressure regulation. Performed all necessary piping modifications to accommodate new boiler configuration and ensure proper steam distribution throughout the system. Replaced two main line steam vents to optimize air elimination and system efficiency. Installed new White-Rodgers programmable digital thermostat for enhanced temperature control and energy management. Ran dedicated electrical circuit to support tankless water heater operation. Installed new circuit breaker in existing electrical panel, labeled appropriately for boiler and h