HVAC & Plumbing Services in Cleveland Heights, OH

Performed comprehensive heating maintenance on a 10-year-old boiler system. Conducted combustion analysis testing with readings showing oxygen levels at 6.4%, carbon monoxide at 4 ppm, and carbon dioxide at 2.2%, with stack temperature at 73.5°F and ambient temperature at 101°F. All system parameters verified within acceptable operating ranges for safe and efficient operation.

Removed existing galvanized water supply line from meter to copper transition point and replaced with PEX piping system. Installed 30 feet of 1/2" blue PEX with brass adapters and fittings, including a 1/2" brass 90-degree elbow on the riser under stairs. Abandoned existing cold water galvanized line from utility tub and rerouted supply from main trunk line to front exterior spigot. Installed new frost-free hose bib at exterior location. Completed installation included three 1/2" PEX 90-degree fittings, two male adapters, one 1/2" brass 90-degree elbow, one 1/2" brass plug, and three 1/2" press valves for shutoff capability throughout the system.

Responded to service call for separated floor vent register following previous installation. Inspected and secured loose floor register in hallway, ensuring proper fit and alignment with ductwork. Verified register is now stable and properly seated in opening to prevent future separation.

Performed comprehensive annual maintenance and tune-up on 20-year-old hydronic heating system. Inspected boiler unit, expansion tank, circulator pump, zone valves, and all associated piping and connections. Verified proper operation of all mechanical components, tested safety controls, and confirmed system pressurization within manufacturer specifications.

Responded to active leak under kitchen sink originating from garbage disposal unit. Upon inspection, identified leak at disposal discharge connection to drain piping. Tightened disposal flange and discharge elbow fittings, verified all PVC drain connections were secure, and tested system under full water flow to confirm leak was resolved.

Installed new exterior hose bib with half-inch valve by accessing cold water supply line through basement wall opening. Relocated existing plumbing in basement ceiling to accommodate new installation, ran copper supply line, and mounted outdoor spigot on exterior siding. Wall opening and drywall repair remained customer responsibility per agreement.

Completed comprehensive tune-up maintenance on 23-year-old furnace system located in basement. Inspected heat exchanger fins, blower assembly, and motor components; all systems found to be operational with normal dust accumulation present. Documented equipment condition through photographic inspection of internal components including blower housing, mounting hardware, and electrical connections.

Responded to service call for gas line capping at fireplace location. Upon arrival, accessed utility area and successfully capped the gas line feeding the fireplace to ensure safe disconnection. Documented existing plumbing conditions including copper supply lines with condensation present, indicating proper cold water flow through the system.

Conducted comprehensive assessment of 5-year-old boiler system that was improperly installed, documenting extensive installation deficiencies including corroded copper piping with severe verdigris oxidation and improper pipe routing. Prepared detailed replacement estimate addressing code violations, deteriorated components, and necessary corrections to bring system up to manufacturer specifications and industry standards.

Responded to storm sewer cleanout request and cleared accumulated debris, leaves, and organic matter from exterior drain access point. Removed blockage material from corroded metal drain ring and surrounding cavity to restore proper drainage function and prevent water backup.

Removed existing Insinkerator garbage disposal unit from under-sink mounting assembly and disconnected all plumbing connections and electrical supply. Installed new Insinkerator disposal unit, securing it to the sink flange with proper mounting hardware, reconnecting drain lines and restoring power connection. Tested unit for proper operation, verified no leaks at connections, and confirmed drain functionality through the disposal and sink basin.

Performed comprehensive tune-up on 15-year-old air conditioning system operating normally at time of service. Inspected outdoor condensing unit, refrigerant lines, and electrical components per standard maintenance protocol. Addressed customer concern regarding gap in foam line insulation on exterior refrigerant lines by inspecting insulation condition and verifying proper coverage. Cleared accumulated debris including leaves and organic matter from around outdoor unit base and foundation area to ensure proper airflow and drainage. Verified all mechanical connections secure and system operating within manufacturer specifications.

Completed comprehensive routine maintenance and tune-up on a 4-year-old furnace system for active maintenance plan member. Performed full system inspection including control board diagnostics, electrical connections verification, and combustion analysis using calibrated testing equipment. All measured parameters including combustion efficiency readings of 119 and 22 confirmed proper furnace operation within manufacturer specifications. Verified all safety controls, gas valve operation, wiring integrity, and pressure switches functioning correctly with no deficiencies noted.

Completed comprehensive fall tune-up on residential forced-air furnace system manufactured in April 2023. Performed standard preventive maintenance protocol including visual inspection of all accessible components, verification of proper combustion and venting through white PVC condensate lines, electrical system testing at 115V/60Hz/1-phase specifications, and confirmation of operational parameters within manufacturer specifications per AHRI certification requirements. All equipment found operating within normal parameters with no deficiencies noted; system ready for heating season under active membership maintenance agreement.

Conducted estimate for complete HVAC system replacement including air conditioning condensing unit and air handler. Inspected existing attic-mounted air handler installation with connected flexible ductwork and assessed equipment condition. Completed yard placement worksheet documenting all required measurements and setback distances for proposed outdoor condensing unit location in compliance with municipal placement requirements and ANSI/AHRI sound rating specifications.

Assessed 25-year-old commercial air conditioning system with failed condenser fan motor located in exterior service alley. Unit showed extensive age-related deterioration, surface contamination, and complete fan assembly failure rendering system inoperable. Provided comprehensive replacement estimate for new commercial HVAC system scheduled for installation, including removal of existing equipment, proper disposal, and installation of appropriately-sized replacement unit to restore cooling capacity to facility.

Completed winter maintenance tune-up on hot water boiler system in duplex unit. Performed standard seasonal inspection, verified operational status of all components, and documented existing conditions including aging piping infrastructure with visible corrosion on copper fittings and horizontal supply lines. Unit confirmed operational with no immediate service issues identified at time of inspection.

Completed scheduled annual maintenance and tune-up on residential boiler system. Performed comprehensive inspection of heat exchanger copper tubes, verified proper operation of all components, and confirmed system is functioning efficiently with no issues detected.

Completed winter maintenance tune-up on hydronic boiler system in utility room. Performed comprehensive inspection of boiler components, burner assembly, and heat exchanger; checked all safety controls and operating pressures. Noted corrosion present on horizontal piping connections with standing water in drain pan beneath system, indicating potential slow leak or condensate drainage issue that should be monitored.

Performed comprehensive tune-up and inspection on 5-year-old furnace system. Heat exchanger and evaporator coils showed significant dust, lint, and debris accumulation affecting system efficiency. Completed full system cleaning, verified proper operation of all components, and restored unit to optimal performance standards per manufacturer specifications.