HVAC & Plumbing Services in Cleveland Heights, OH

Responded to a water heater leak originating from the outlet connection on a previously installed tanked unit. Upon arrival, identified active water discharge from the hot water outlet fitting causing floor saturation in the installation area. Performed pressure testing using diagnostic gauge to verify system pressure and identify the source of the leak at the outlet connection. Addressed the faulty outlet fitting, secured all connections, and verified proper seal integrity. Cleaned up standing water from the concrete floor surface surrounding the unit. Conducted final pressure test to confirm leak resolution and proper system operation before restoring unit to service.

Performed comprehensive preventive maintenance on an 11-year-old Goodman outdoor condensing unit, model W1AC06SA181A. System was operational with no reported issues at time of service. Completed full tune-up inspection including visual assessment of electrical components, verification of manufacturer specifications, and examination of blower wheel assembly. Noted moderate dust and debris accumulation on blower wheel blades and housing, consistent with normal operation over extended service interval. All electrical specifications confirmed per nameplate data: 208-230V, 1PH, 60HZ operation. Unit remains in serviceable condition for continued operation.

Completed preventative maintenance tune-up on 19-year-old residential air conditioning system located in backyard. Performed comprehensive inspection of cooling equipment, verified operational parameters, and assessed system performance in accordance with manufacturer specifications.

Conducted on-site boiler replacement estimate in residential basement mechanical room. Assessed existing conditions including aged brick walls with deteriorated mortar, current water heating equipment with copper and PVC piping connections, and overhead ductwork with insulation. Evaluated confined workspace limitations, existing plumbing infrastructure, and necessary access points for equipment removal and installation. Documented mechanical room layout, pipe routing configurations, and structural considerations for new boiler system installation planning.

Completed annual preventative maintenance on residential air conditioning system. Performed comprehensive tune-up including temperature diagnostics at outdoor condenser unit, verified proper system operation, and inspected all accessible components. Unit found to be functioning within normal parameters with no deficiencies noted at time of service.

Completed installation of new split-system air conditioning unit for second-floor climate control in attic space. Installed new air handler with metal mounting stand, high-efficiency condenser unit, auxiliary drain pan for overflow protection, condensate pump for proper drainage, and programmable thermostat. Configured flexible insulated ductwork connections to air handler using 8-inch diameter ducts in Y-configuration to distribute conditioned air throughout second-floor zones. All components properly secured to structural framing, electrical connections completed per manufacturer specifications, and refrigerant lines charged to operational levels. System tested and verified operational.

Performed comprehensive preventive maintenance on a 5-year-old residential air conditioning system. Upon arrival, verified unit was operating properly with no reported issues. Conducted complete system inspection including visual examination of outdoor condenser unit, which showed normal wear and dirt accumulation consistent with age. Connected digital manifold gauges to service ports and measured refrigerant pressures and temperatures. Verified refrigerant charge levels were within manufacturer specifications with no indication of leaks. Inspected electrical disconnect box and all electrical connections for proper operation and secure termination. Examined copper refrigerant lines for damage, proper insulation, and secure mounting. Cleaned condenser coil fins to remove accumulated dirt and debris, improving heat transfer efficiency. Checked condenser fan motor operation and lubricated as needed. Verified fan blade condition and proper clearances. Inspected compressor for unusual noi

Completed hot water heating system repair involving draining, refilling, and bleeding air from system to facilitate valve replacement. Removed and replaced faulty 3/4" angle radiator valve (LEGEND 110-104 T-431) on cast iron radiator, requiring radiator removal and reinstallation. Reconnected previously disconnected radiator, bled air from system, and verified proper operation upon completion.

Responded to service call for leaking water heater in residential basement utility room. Upon inspection, determined existing tanked water heater of unknown age was actively leaking with no significant water damage to surrounding concrete block walls or floor. Assessed mechanical room containing water heater, furnace, and associated plumbing and HVAC infrastructure with copper and black iron piping. Documented equipment condition and leak source for repair recommendations.

Completed new sink installation in compact powder room. Installed white porcelain sink with chrome P-trap assembly and connected drain line to existing wall outlet. Installed supply line with shut-off valve and verified all connections for proper sealing and operation. All plumbing fixtures tested and confirmed leak-free upon completion.

Responded to service call for multiple water leaks throughout the property. Repaired leaking outside spigot at exterior foundation, replaced faulty hot water shut-off valve under kitchen sink, and addressed leaking waterline connection at bathroom sink. Photographic documentation revealed corroded pipe fittings with visible rust staining and water damage at appliance base, indicating prolonged moisture exposure. Exterior inspection showed insulated pipes along foundation with exposed copper section requiring attention. All leak sources were identified, connections were secured or replaced as needed, and water flow was restored to proper operating condition.

Completed comprehensive AC tune-up on residential cooling system found operating normally upon arrival. Performed standard preventive maintenance procedures including inspection of blower motor assembly, verification of proper airflow, and examination of internal components. All systems checked and confirmed to be functioning within normal parameters.

Completed comprehensive tune-up service on two heat pump systems including air handler, blower, and hot water heater maintenance. Performed temperature diagnostics on outdoor heat pump unit, recording 57°F readings with digital probe to verify proper refrigerant cycling and system performance. Inspected condensing unit exterior showing normal condensation patterns indicating active operation, checked fan guard security and fasteners, and verified unit stability on gravel pad base. Accessed crawl space to service air handler components and inspect installation integrity beneath floor joists. Evaluated foundation and structural supports for proper clearances and identified moisture-related deterioration on concrete wall surfaces with visible staining and surface degradation requiring monitoring for future remediation. Completed standard preventive maintenance protocols including filter inspection, electrical connection verification, condensate drain assessment, and operational testing

Performed comprehensive cooling system maintenance on residential air conditioning unit. Completed full AC tune-up including inspection of condenser unit, verification of proper system operation, and standard preventative maintenance procedures. System found to be operating within normal parameters at time of service.

Performed comprehensive cooling system maintenance on a 5-year-old Carrier heat pump unit (Model: CNPVP4217AAAAAA) utilizing R-410A refrigerant. Conducted standard diagnostic testing with digital manifold gauges to verify system pressures and performance parameters, ensuring proper refrigerant charge and operational efficiency. Completed routine inspection of electrical connections, condenser coil condition, and fan operation to maintain optimal system performance for the cooling season.

Responded to service call for hot water tank leak inspection and blank thermostat issue. Upon arrival, conducted thorough assessment of plumbing system beneath bathroom vanity, inspecting P-trap assembly and supply lines for signs of moisture or active leaking. Examined HVAC equipment in mechanical room, including light blue condensate pump unit mounted on support brackets with associated drainage hoses and ductwork connections. Verified thermostat functionality and power supply to heating system. Documented existing conditions with photographs for customer records and further evaluation of potential water heater concerns.

Completed full HVAC system replacement including outdoor condensing unit and evaporator coil. Installed new Bryant air conditioning unit on existing concrete pad, established proper refrigerant connections, and performed vacuum test to verify system integrity. All electrical connections secured, refrigerant lines properly connected, and system tested to manufacturer specifications for optimal cooling performance.

Responded to complaint of toilet slow to fill after flushing in 100-year-old residence. Upon inspection, removed tank lid and evaluated internal flush mechanism components. Identified aging fill valve assembly with standard float ball configuration as source of reduced flow rate. Inspected flush valve, flapper, and overflow tube assembly for proper operation. All components showed signs of age-consistent mineral deposits and wear. Tested fill valve operation through multiple flush cycles to confirm slow fill condition. Documented existing blue fill valve mechanism and black flush valve assembly with photographic evidence for service records. Recommended fill valve replacement to restore proper fill time and water flow efficiency.

Completed removal and capping of two deteriorated radiators in residential property. Collected deposit payment and coordinated with appropriate departments for sold repair estimate processing. Documentation and photos captured showing existing conditions of heavily corroded radiator units with extensive paint failure and brass shut-off valves requiring decommissioning.

Responded to service call for boiler system requiring radiator reconnection. Successfully reconnected cast iron radiator unit to boiler system using galvanized pipe fittings and verified proper threading and secure connections. System tested and returned to normal operation with radiator properly integrated into heating loop.