HVAC & Plumbing Services in Cleveland Heights, OH

Completed preventative maintenance on 20-year-old boiler system, including inspection of gas valve assembly, pressure relief valve mechanisms, piping connections, and expansion tank. Air handler maintenance was deferred due to ambient temperature conditions preventing proper AC system evaluation. Customer expressed interest in smart thermostat upgrade for future consideration.

Completed site evaluation for HVAC cooling system addition in commercial or multi-story building space. Assessed existing mechanical room configuration with current dark green air handling unit and ductwork installation. Evaluated rooftop access requirements and determined feasibility for condenser placement, documenting existing equipment layout, ductwork routing through ceiling access points, and available mounting locations for new outdoor condensing unit to provide cooling capacity to the space.

Completed scheduled maintenance on 8-year-old Dunkirk PSB-50 steam boiler system. Performed comprehensive inspection of unit, verified proper operation of all components, checked electrical connections and safety controls, and documented equipment condition with photographs for service records.

Performed annual maintenance on tankless water heater located in basement utility area. Completed descaling flush procedure using vinegar solution circulated through the unit with pump and hoses to remove mineral buildup from heat exchanger. Inspected all plumbing connections, inlet/outlet valves, and mounting hardware for proper operation and secure installation.

Completed maintenance inspection on 20-year-old steam boiler system located in basement. Performed visual assessment of burner assembly, heat exchanger sections, and gas supply components. Inspected burner tubes showing purple flame indication, examined cast iron heat exchanger sections displaying moderate dust and sediment accumulation on outer sections with center section appearing cleaner. Noted age-appropriate surface discoloration and minor deposits on heat exchanger fins consistent with two decades of operation. System operational at time of inspection with burner assembly functioning properly.

Responded to service call for inconsistent hot water delivery and active leak from temperature and pressure relief valve discharge tube on residential tanked water heater. Upon inspection, diagnosed failed T&P relief valve allowing water to discharge through the drain tube, contributing to inconsistent system performance. Replaced defective temperature and pressure relief valve with new code-compliant unit, tested for proper operation and verified no leaks at valve body or discharge tube connections. System restored to normal operating condition with consistent hot water delivery throughout residence.

Completed scheduled boiler maintenance under home plan agreement. Thoroughly inspected heat exchanger components, including primary heat exchanger fins and secondary heat exchanger drum assembly. Both heat exchangers showed significant rust accumulation and corrosion on metal surfaces, indicating extended service life and exposure to moisture during normal operation. Documented current condition of copper-alloy fins and cylindrical pin-type heat exchanger with photographic evidence for maintenance records. All components remain functional despite visible oxidation and patina buildup typical of aging boiler systems.

Conducted site assessment for mini-split installation in sunroom with natural wood paneling and multiple windows. Evaluated space layout, electrical requirements, and optimal placement for indoor air handler and outdoor condensing unit to provide efficient heating and cooling for the multipurpose recreational area.

# HVAC Maintenance - Heating System Service Completed comprehensive annual heating maintenance on a 13-year-old MVP boiler system as part of recurring Home Plan service. Performed full system inspection including burner assembly examination, where all five burner tubes were assessed for proper operation and flame characteristics. Noted normal operational wear with surface oxidation present on burner components consistent with system age. Inspected gas manifold, ignition system components, and flame sensor wiring for proper connections and functionality. Evaluated copper piping network and hydronic distribution system, including brass valve assemblies and zone controls. Verified proper operation of zone valves and confirmed all mechanical connections were secure without leaks. Checked control unit mounted to piping system for proper programming and operation. Tested safety controls and limit switches to ensure system shutdown protocols function correctly. Verified adequate combustion

Removed blower motor and wheel assembly from furnace and performed thorough cleaning of all components to restore proper airflow throughout the system. Service completed to improve overall HVAC performance and air circulation efficiency.

Conducted boiler replacement estimate for existing Dunkirk PVSV5 unit showing significant age and deterioration. Site assessment revealed severe moisture infiltration issues with extensive water damage to surrounding concrete walls, heavy frost and ice accumulation on copper piping, and compromised mechanical room conditions requiring attention during replacement installation.

Completed comprehensive winter maintenance and tune-up on 4-year-old Bryant gas furnace system. Performed full system inspection including burner assembly operation, heat exchanger examination, ignition system verification, and combustion analysis. Observed proper blue flame characteristics across all burners indicating optimal gas-air mixture and efficient combustion. Inspected and verified proper operation of flame sensor, limit switches, and safety controls. Checked electrical connections, tested blower motor operation, and confirmed proper airflow throughout system. All components found operating within manufacturer specifications with no deficiencies noted. System ready for heating season operation.

Responded to no-heat call on 5-year-old furnace system. Upon inspection, found aged control board assembly with visible corrosion on components and connection points, along with dust accumulation on circuit board and filter material. Diagnosed failed relay on control board as cause of system failure, replaced defective relay, cleaned electrical connections, and verified proper system operation with successful heat call.

Replaced deteriorated clay wye section where first floor stack connects to basement floor drain due to moisture damage and structural failure. Broke open concrete floor, removed compromised clay piping, and installed new PVC section with proper connections. Bedded replacement pipe in gravel for stability and drainage, then repoured and finished concrete floor to restore surface integrity.

Completed comprehensive AC tune-up on 9-year-old HVAC system. Performed full inspection of blower assembly, motor, and internal components. Verified proper operation of blower wheel and squirrel cage fan, checked all electrical connections and wiring harnesses, and inspected refrigerant lines for integrity. Documented equipment condition with interior access photos showing normal wear patterns consistent with system age. All components functioning within normal parameters upon completion of maintenance service.

Responded to no-heat call for boiler not lighting. Upon inspection, found ignition system failure preventing burner from firing. Cleaned flame sensor, inspected gas valve assembly and sight glass, verified proper gas flow, and tested ignition sequence. System restored to normal operation with burner lighting properly and heating cycle functioning as designed.

Completed HVAC estimate for air conditioning system addition to existing forced air furnace installation. Assessed 27-year-old furnace unit currently in service, located in basement mechanical room. Evaluated existing equipment condition, including blower motor assembly, electrical components, and ductwork configuration to determine compatibility with proposed cooling system integration. Documented current furnace specifications and physical layout for accurate system design and equipment sizing recommendations.

Responded to service call for leaking sight glass on Republic brand steam boiler system, over 51 years old. Upon inspection, confirmed active leak at sight glass gasket requiring replacement. Replaced failed gasket with new component to restore proper seal and prevent continued water loss. Verified sight glass assembly secure with no additional leaks present. System operational upon completion of repair.

Completed comprehensive maintenance service on a 15-year-old gas heating system. Performed combustion analysis using diagnostic equipment to verify proper CO and CO2 levels, with temperature readings indicating normal operating parameters at 90.9°F. Inspected blower wheel assembly, confirming fan blades and motor hub are in serviceable condition with normal wear patterns for equipment age. All system components tested and operating within manufacturer specifications.

Completed scheduled maintenance on a 4-year-old gas-fired boiler system with multi-zone hydronic heating distribution. Inspected manifold assembly with three zone valves, verified proper operation of circulator pumps, examined copper piping connections and fittings for leaks, and assessed integrated HVAC ductwork components. All equipment found operating within normal parameters with no immediate service needs identified.