HVAC & Plumbing Services in Cleveland Heights, OH

Responded to service call for water pressure issues at residential property. Upon arrival, conducted visual inspection of water heater and HVAC system in utility area. Documented existing equipment conditions including water heater model XC10S36F100 (serial P371540975) and associated mechanical systems. Customer requested second opinion evaluation for water pressure concerns to compare with previous estimate from another provider.

Responded to service call for 3-year-old steam boiler system with reported pipe corrosion. Upon inspection, identified severe corrosion on horizontal steam pipe with extensive rust buildup, pitting, and metal deterioration requiring immediate repair. Documented existing plumbing configuration including copper risers, brass fittings, and connection points to facilitate proper repair planning and parts procurement.

Responded to service call for 16-year-old boiler system operating at insufficient pressure (5-6 PSI instead of required 12+ PSI). Performed comprehensive system inspection and tuneup, checking all components for proper operation. Inspected expansion tank, pressure relief valve, and associated piping connections. Verified all safety controls, burner operation, and heat exchanger condition. Adjusted system pressure to manufacturer specifications and confirmed proper pressurization. Tested all mechanical components including circulator pump, zone valves, and control systems to ensure optimal performance and safe operation.

Responded to no heat call for 15-year-old furnace. Upon arrival, discovered unit was actually a boiler with severe corrosion and active water leakage at base, causing extensive rust staining and pooling on concrete floor. Documented heavy deterioration of metal casing where unit meets floor, compromised integrity of lower sections, and sediment accumulation in sight glass. Provided replacement estimate due to age of equipment and extent of corrosion damage making repair cost-prohibitive.

Performed comprehensive tune-up on 23-year-old furnace with no reported issues. Conducted temperature diagnostics using digital multimeter, recording heat exchanger temperature of 357.5°F. Removed, inspected, and cleaned flame sensor rod to ensure proper ignition and flame detection capability for reliable system operation.

Responded to a burst water line feeding an outdoor spigot that had failed during the summer months. Accessed the supply line through the basement ceiling joists, removed the damaged section of pipe, and installed new blue PEX tubing with brass fittings to connect to the existing copper piping. Verified the outdoor hose bib mounted on the exterior brick wall was functioning properly and tested the system for leaks after restoring water pressure.

Responded to service call for toilet leak from upstairs bathroom causing water damage to ceiling below. Upon inspection, identified severely corroded horizontal drain pipe in basement utility area with extensive rust deterioration and compromised structural integrity. The corroded pipe section was causing water to leak through deteriorated areas when upstairs toilet was flushed, resulting in water infiltration into the ceiling below. Documented existing plumbing infrastructure including multiple connection points, PVC piping, and associated fittings. Photographed corroded pipe section showing heavy rust accumulation and flaking metal, as well as upstairs bathroom with white porcelain toilet and decorative tile work to document service location. Recommended immediate replacement of corroded drain pipe section to prevent further water damage and restore proper drainage function.

Responded to no-heat call for furnace located in basement. Upon arrival, performed diagnostic inspection and found unit was not igniting. Checked thermostat settings, verified power supply, and inspected gas valve operation. Cycled system and confirmed ignition sequence initiated properly with burners lighting successfully. Observed steady blue flames across all burner ports indicating proper gas-air mixture and combustion. Verified all safety controls functioning correctly and system operating within normal parameters. Unit restored to full heating operation.

Responded to service call for radiator valve replacement. Upon arrival, removed existing failed Honeywell thermostatic radiator valve from baseboard heating system. Disconnected copper supply line from radiator, removed deteriorated baseboard trim to access valve assembly and fittings. Installed new Honeywell replacement valve with proper brass fittings, reconnected copper piping, and tested system for proper operation and leak-free connections. Radiator heating function restored to normal operation.

Completed full boiler replacement in residential basement, installing New Yorker model CG70 cast iron hot water boiler rated at 210,000 BTUs. Installation included new Amtrol expansion tank, pressure reducing valve with backflow preventer, automatic air vent, and circulator pump. Performed all near boiler piping modifications using copper pipe and brass fittings, and installed new flue pipe connection to existing chimney. Reused existing thermostats, zone valves, and zone panel from previous system. System tested and operational with limited lifetime warranty on heat exchanger, 5-year parts, and 5-year labor coverage.

Responded to no heat complaint on boiler system that had been experiencing issues for approximately one year. Upon arrival, inspected boiler system and associated components including copper piping, valves, and circulation equipment in mechanical room. Customer reported valve was in open position but system was not producing heat. Performed diagnostic evaluation of boiler controls, zone valves, and heating distribution system to identify cause of heating failure and restore proper operation.

Completed comprehensive maintenance service on a 2-year-old commercial gas furnace as part of the MVP HEAT program. Performed full system inspection including blower assembly examination, verified proper operation of all components, and documented equipment condition with photographic records.

Conducted site assessment for HVAC replacement on commercial rooftop installation. Documented existing ductwork system showing aged metal supply duct with visible wear, weathered ceiling surfaces with water damage indicators, and supporting infrastructure requiring evaluation. Captured equipment positioning and structural conditions to develop comprehensive replacement estimate for system upgrade.

Responded to heating system failure and diagnosed faulty gas valve on tankless water heater unit. Removed access panel, disconnected electrical connections and gas lines, and replaced defective gas valve assembly with new OEM component. Verified proper operation with multimeter readings, tested all electrical connections, and confirmed unit fired correctly with no gas leaks detected.

Completed warranty replacement of residential water heater in basement utility area. Removed existing failed unit and installed new white cylindrical water heater with proper connections including copper supply lines, expansion tank at base, and venting system. Configured control assembly with temperature settings and verified all plumbing connections, gas line hookup via flexible corrugated tubing, and proper clearances around unit. Service was scheduled after completion of separate boiler preventive maintenance to avoid conflicts between technicians working in same space.

# HVAC Maintenance - Heating System Performed annual maintenance on a 7-year-old residential boiler system. Conducted comprehensive inspection of boiler unit, heat exchanger, venting system, and associated piping including pressure testing and safety control verification. All components found operating within normal parameters; system returned to service with no issues identified.

Performed annual maintenance on a 10-year-old steam boiler system. Inspected unit serial number documentation and verified equipment specifications against manufacturer records. All components operating within normal parameters upon completion of tune-up procedures.

Completed scheduled maintenance on a 10+ year old Luxaire gas furnace, model LM9M075C16MP11A with 100,000 BTUH input capacity. Performed comprehensive system inspection including burner assembly cleaning, heat exchanger examination, blower motor lubrication, and filter replacement. Verified proper combustion and airflow, tested safety controls, and confirmed all operational parameters within manufacturer specifications for this Category IV direct vent unit.

Completed Home Protection Plan maintenance visit on a 2-year-old gas furnace system. Performed comprehensive inspection of furnace unit, verified proper operation of all components, checked venting and drainage connections, and documented equipment condition with photos. All systems operating within normal parameters.

Completed annual preventive maintenance on 6-year-old gravity steam boiler system. Performed comprehensive tune-up including inspection of sight glass water level indicator, low water cutoff operation verification, and examination of all piping connections and fittings. Unit operating properly with no deficiencies noted; all components functioning within normal parameters.