HVAC & Plumbing Services in Cleveland Heights, OH

Responded to service call for non-operational tanked water heater with suspected pilot light issue. Upon arrival, inspected gas-fired water heater unit located in basement utility area. Assessed pilot assembly, thermocouple, and gas control valve for proper function. Verified gas supply to unit and checked for any safety lockouts. Relit pilot light following manufacturer specifications and confirmed stable flame. Tested burner ignition cycle and verified water heater returned to normal heating operation. Unit restored to full functionality.

Installed a chrome two-handle widespread lavatory faucet with pop-up drain assembly on existing marble vanity countertop. Provided and installed a Gerber Avalanche elongated toilet with matching seat, new wax ring seal, and supply line to complete the bathroom fixture upgrades.

Replaced two existing toilets with new fixtures in residential property. Removed old units, installed new toilets with proper wax ring seals and water supply connections, tested for leaks and proper flushing operation. All debris removed from work areas and installations verified to be functioning correctly.

Responded to reported AC coil leak. Upon inspection, accessed the evaporator coil through the air handler opening and confirmed refrigerant leak at the indoor coil assembly. Documented existing conditions including coil access point, condensate drain system with pump assembly, and surrounding mechanical components for repair recommendations and customer review.

Completed scheduled furnace tune-up on two-year-old heating system that was operating normally at time of service. Performed comprehensive maintenance including combustion analysis testing to verify proper efficiency levels, CO2 readings, and temperature differentials, with all measurements falling within acceptable parameters. Inspected blower wheel assembly and confirmed clean condition with no debris accumulation or mechanical wear on blades or motor housing.

Responded to ceiling leak originating from bathroom plumbing in century-old residential structure. Accessed affected area through ceiling hatch to identify source of water intrusion causing visible staining on textured ceiling surface. Inspected basement plumbing connections and HVAC system drainage lines for potential leak points. Documented water damage patterns and equipment configuration for repair assessment. Customer also requested separate HVAC cooling system consultation to be scheduled.

Removed and replaced failed angle radiator trap in corner location where extensive water damage to flooring and wall indicated long-term leakage from corroded original fixture. Verified proper operation of new trap, confirmed no leaks, and ensured system functionality upon completion.

Conducted site assessment for mini split installation estimate. Evaluated existing electrical panel capacity and bedroom location for indoor unit placement, documented conditions with photos, and provided pricing proposal valid for 30 days.

Performed temporary disconnect of 22-year-old outdoor air conditioning unit to facilitate property renovations. Disconnected electrical power at unit disconnect, capped refrigerant lines, and secured all components to protect system during construction work. Unit showed no pre-existing issues and will be available for reconnection upon completion of renovation work.

Responded to service call for 10-year-old air conditioning system not cooling and experiencing freeze-up conditions. Upon arrival, performed comprehensive diagnostic evaluation of both indoor and outdoor HVAC components. Inspected York furnace installation in basement mechanical room along with associated ductwork, refrigerant lines, and auxiliary equipment including dehumidifier and wall-mounted air handler. Evaluated outdoor condenser unit, noting overgrown vegetation surrounding equipment which can restrict airflow and reduce system efficiency. Documented current system conditions through photographic evidence showing complete HVAC installation layout and outdoor unit placement. Based on age of equipment, freeze-up symptoms, and overall system assessment, provided detailed estimate for complete HVAC system replacement to address cooling deficiencies and prevent future operational failures.

Completed scheduled cooling tune-up on a 4-year-old residential cooling system consisting of an outdoor condenser unit (Model NXA436GKC101, Serial E181309405) and indoor air handler. Performed comprehensive maintenance inspection including visual assessment of outdoor unit positioned in landscaped area against brick wall, verified unit accessibility, checked refrigerant charge specifications (factory charge 9.42 lbs), confirmed electrical ratings (208-230V), and documented equipment condition through photographic records showing proper installation and adequate clearances around condenser with protective grille intact.

Conducted comprehensive site assessment and provided replacement estimate for commercial rooftop package unit cooling system. Evaluated existing equipment access requirements, documented current HVAC unit condition with photographs, and confirmed specifications for new installation including duct smoke detector integration and programmable thermostat compatibility.

Responded to no-communication issue between thermostat and 11-year-old air handler unit located in attic. Diagnosed and resolved communication failure, restoring proper system operation. Also performed routine maintenance service on ductless mini-split system with single indoor head unit, including cleaning filters, checking refrigerant levels, and verifying proper operation of all components.

Completed comprehensive air conditioning tune-up on a four-year-old residential system. Performed standard maintenance procedures on both the outdoor condenser unit and indoor air handler, including inspection of electrical components, refrigerant levels, and airflow. System found to be operating within normal parameters with no issues identified or repairs needed.

Responded to gas leak service call following utility company inspection and gas shutoff. Assessed existing gas line configuration from trunk line to dryer location, including compromised valve assembly requiring replacement. Evaluated scope of work for gas line re-piping as specified by utility company, including necessary appliance relocation to access and replace affected piping sections. Documented existing pipe conditions and valve assembly showing age-related deterioration. Site prepared for gas line replacement work to meet utility company requirements for service restoration.

Performed drain snaking service to clear obstruction in kitchen sink drain line. Successfully cleared blockage and restored proper drainage flow. Installed new 50-gallon, 40,000 BTU short water heater in basement utility area. Connected copper supply lines to unit, verified proper venting configuration, and tested all connections for leaks. Confirmed water heater operation and adequate hot water delivery throughout system. Inspected under-sink plumbing assembly, verified P-trap configuration and all PVC connections are secure and functioning properly. All work completed to code specifications with system operating as intended.

Conducted on-site assessment for mini split installation in attic space. Evaluated existing heating system consisting of portable oil-filled radiators and documented current room conditions including electrical outlet locations, wall construction, and available mounting surfaces. Photographed installation area to determine optimal placement for indoor air handler unit and provided estimate for ductless mini split system.

Performed preventive maintenance tune-up on Fujitsu ductless mini-split system. Inspected indoor wall-mounted unit, verified operational status of all components, and documented equipment condition with photos. System operating within normal parameters at time of service.

Performed comprehensive AC tune-up on 10-year-old cooling system that was operating properly at time of service. Conducted full system diagnostics using digital manifold gauges to measure refrigerant pressures and temperatures, inspected outdoor condensing unit and indoor air handler components, verified proper airflow through ventilation system, and confirmed all operational parameters were within manufacturer specifications. System tested and left in good working condition.

Responded to service call for inadequate hot water supply throughout residence. Inspected American Water Heater Company 40-gallon natural gas tanked water heater, model BFGG140T403NOV, rated at 40,000 BTU/HR input with 53.9 gallon recovery rate. Documented unit specifications and condition via photographs for service records.