HVAC & Plumbing Services in Cleveland Heights, OH

Performed maintenance inspection on a 10-year-old furnace system. Unit was accessed and evaluated for operational efficiency and safety compliance. Documentation completed with photographic records of the installation location and surrounding area.

Completed comprehensive boiler inspection in mechanical room. System evaluated included blue residential boiler unit with associated piping network showing age-related wear and oxidation on multiple pipe runs. Documented current equipment condition, piping configuration, and overall system status through photographic records for maintenance planning purposes.

Completed scheduled heating maintenance on a 10-year-old York Category IV direct vent forced air furnace (Model: YP9C080B12MP12CA, 80,000 BTUH input). Performed comprehensive system inspection including burner assembly examination, heat exchanger visual inspection, blower motor operation verification, and air filter assessment. Tested gas pressure, confirmed proper venting function, verified temperature rise within manufacturer specifications of 40-70°F, and ensured all safety controls were operating correctly. System is functioning properly with no issues identified at this time.

Responded to a clogged kitchen sink call and performed diagnostic inspection of the drainage system. Upon arrival, examined the P-trap assembly and associated PVC plumbing connections beneath the sink, which appeared to be in standard operational condition. Additionally inspected the vertical drain pipe where it exits through the floor, noting significant rust and corrosion buildup on the metal piping that may require future attention to prevent potential drainage issues or structural failure of the pipe.

Responded to report of leak in wall at residential property. Upon inspection, identified moisture intrusion behind shower wall tile assembly. Accessed plumbing connections for dual shower valve system, isolated source of leak to faulty valve stem seal on chrome-finished mixing valve. Replaced defective valve cartridge and seal assembly, tested system under pressure, and confirmed proper operation with no further water penetration. Shower controls restored to full functionality.

Responded to gas leak service call and measured 120 standard cubic feet of gas leakage in basement area. Upon inspection, identified severely corroded copper gas line supplying the stove, with extensive rust deterioration and flaking at base and lower sections requiring complete line replacement. Coordinated with property occupant regarding temporary gas shutoff procedures and documented equipment conditions with photographs for replacement planning.

Provided comprehensive estimate for complete HVAC system replacement on existing Payne air conditioning unit. Documented current equipment condition, mounting hardware, refrigerant line configuration, and electrical connections to prepare detailed replacement proposal for customer consideration.

Completed installation of a new 5-zone Bryant ductless mini-split heat pump system. Mounted three 9K BTU high wall units in bedrooms, one 12K BTU high wall unit in dining room, and one 12K BTU floor console unit in living room. Routed refrigerant lines and electrical connections through basement to outdoor condenser unit positioned at rear of home. All indoor units mounted per specifications with clean line sets concealed where possible. System tested, commissioned, and verified operational across all zones.

Responded to service call for rooftop Carrier Gemini Select unit with reported coil leak. Inspected dual compressor system and evaporator coil assembly, documented equipment condition and leak location with photos for service records. Unit requires coil repair or replacement to resolve refrigerant leak issue.

Completed annual tune-up and maintenance on 5-year-old basement boiler system per member service agreement. Performed comprehensive inspection of boiler components, verified combustion efficiency readings using calibrated digital analyzer showing operational temperature at 72°F, checked all electrical connections and internal mechanical components with access panel open, and inspected associated piping infrastructure including black steel supply lines and copper distribution piping. All systems tested and found operating within manufacturer specifications.

Performed comprehensive coil cleaning service on Goodman R22 central air conditioning system, model N-40. Completed three-hour maintenance procedure to restore optimal heat transfer efficiency and system performance.

Completed full HVAC system replacement including installation of new two-stage air conditioning unit, furnace, evaporator coil, and Ecobee smart thermostat. Performed comprehensive system diagnostics and commissioning, verifying proper refrigerant charge, airflow measurements, and temperature differential across the coil to ensure optimal system performance and efficiency.

Removed two existing water heaters from the basement utility area and installed a single 50-gallon residential water heater with proper copper piping connections. Installed a white expansion tank on the supply line and completed electrical bonding per code requirements to ensure safe operation of the new system.

Completed comprehensive boiler tune-up including combustion analysis, which confirmed proper operation with oxygen levels at 6.7%, carbon monoxide at 0.16 ppm, CO2 at 7.2%, and stack temperature at 290.9°F. Replaced batteries in Emerson thermostat and adjusted mounting to allow easier future battery access by homeowner. Verified expansion tank pressure at 17 PSI and documented system parameters for service records.

Conducted on-site assessment of existing boiler system located in basement mechanical room to provide replacement estimate. Upon arrival, accessed property via lock box and performed thorough evaluation of aging teal-colored boiler unit, associated piping infrastructure, and installation conditions. Documented current system configuration including insulated supply lines, pipe connections, and mechanical room layout through photographic documentation. Assessed basement structural elements, clearances, and access points to determine replacement requirements and installation parameters for new boiler system.

Responded to customer report of toilet flushing abnormally. Upon inspection, removed tank lid and identified internal component issues including improper float adjustment and aging tank hardware with visible mineral deposits and waterline staining. Inspected fill valve assembly, flapper mechanism, and float connections to diagnose malfunction causing irregular flush cycle and water flow concerns.

Replaced weathered exterior hose bib with new frost-free faucet on light blue lap siding exterior wall. Installed 1/2" press ball valve in interior utility room to provide proper shut-off control for the outdoor faucet line, utilizing press connection technology on existing copper supply piping. All connections tested and verified leak-free with no issues upon completion.

Completed comprehensive cooling maintenance on 16-year-old residential air conditioning system during scheduled 12p-4p service window. Performed full system diagnostics using digital testing equipment to measure electrical values and refrigerant pressures, inspected outdoor condensing unit including fan assembly and condenser coil, and evaluated overall system performance. Unit is approaching end of recommended service life and customer should consider replacement options in near future.

Responded to water leak investigation in 1920s-era residential property. Upon inspection, identified toilet tank as source of leak with significant water damage to surrounding wooden framing and structural components. Tank interior showed extensive brown water staining, mineral deposits, and discolored water indicating chronic leak and corrosion of flush valve assembly. Documented deteriorated wooden framing compromised by long-term moisture exposure, rust staining on metal components, and sediment buildup in tank bottom. Recommended replacement of corroded flush valve system and repair of water-damaged structural framing to prevent further deterioration.

Responded to service call for AC unit not cooling and displaying error message. Upon arrival, found electrical disconnect switch in OFF position at outdoor condenser unit. Restored power to system by switching disconnect to ON position, which cleared the service error message and restored normal cooling operation to the residence.