HVAC Services in Cleveland, OH

Conducted rooftop estimate for commercial HVAC unit replacement and assessment of two tube heaters. Documented existing Carrier package unit condition, noting significant rust staining on concrete platform and curb adapter, and reviewed installation specifications including mounting requirements, clearances, and equipment weights for proper system sizing and replacement planning.

Completed routine maintenance on two 6-year-old gas furnaces. Performed comprehensive inspection of both heating systems, including examination of blower assemblies, electrical connections, and internal components. Conducted combustion analysis testing using calibrated digital instrumentation to verify proper burner operation and efficiency levels on both units. All systems found operating within manufacturer specifications with no deficiencies noted.

Conducted on-site evaluation for add-on air conditioning system to existing forced air heating setup. Assessed current Carrier furnace installation and existing ductwork infrastructure in basement mechanical room to determine compatibility and requirements for AC integration. Documented existing HVAC configuration including supply ductwork, PVC drainage lines, and available space for evaporator coil placement above furnace unit. Evaluated structural conditions of ceiling joists showing water damage and deterioration that may require attention during installation. Provided comprehensive estimate for complete air conditioning system addition including necessary ductwork modifications, electrical requirements, condensate drainage integration with existing PVC system, and outdoor condenser unit placement.

Responded to no-flush condition on Kohler toilet. Found toilet handle disconnected from flapper chain, preventing flush valve activation. Reconnected handle lift arm to flapper chain and adjusted chain length for proper slack and operation. Tested flush mechanism multiple times to verify full flapper lift and complete flush cycle. System restored to normal operation.

Conducted on-site evaluation of 12-year-old residential furnace system located in basement utility area to provide replacement estimate. Inspected existing gray metal furnace unit, associated PVC venting, condensate drainage system, and connected ductwork. Documented current system configuration including air handler, refrigerant lines, and plumbing connections. Captured photographic documentation of equipment condition and installation layout for estimate preparation. Provided replacement quote and scheduled follow-up appointment with customer requiring advance notification.

Conducted comprehensive site assessment for ductwork renovation and additional vent installation. Evaluated existing mechanical infrastructure including exposed ceiling joists, wall framing, and current HVAC distribution system to determine scope of modifications required. Documented structural conditions showing significant drywall removal and exposed framing members necessary for ductwork reconfiguration and new vent placement.

Completed annual maintenance on 11-year-old air conditioning system. Performed standard tune-up procedures including inspection of outdoor condensing unit, verification of electrical connections at disconnect box, and assessment of refrigerant lines and overall system condition.

Responded to callback for persistent bathroom drain backup issue following previous service visit. Upon inspection, confirmed that drainage problems stem from deteriorated pipe sections in the existing plumbing system rather than the initial repair work performed. Documented existing pipe conditions showing age-related deterioration and provided estimate for replacement of affected pipe sections to resolve ongoing drainage concerns.

Conducted on-site assessment of residential steam heating system to evaluate cast iron radiator requiring replacement. Inspected vintage multi-column radiator located beneath staircase, documenting existing unit configuration, mounting hardware, and connection points. Evaluated radiator condition noting surface wear and age-related deterioration. Photographed installation area including clearances, piping connections, and surrounding space constraints for accurate replacement specifications. Prepared comprehensive quote for radiator replacement including removal of existing unit and installation of new component compatible with current steam boiler system.

Installed ductless mini-split system with console-style indoor unit mounted on third floor landing and outdoor condenser positioned at rear of building alongside existing AC equipment. Due to roofline constraints limiting installation options, routed refrigerant lines and electrical connections through basement to reach rear condenser location. Installed insulated line set with proper pitch for condensate drainage, made refrigerant connections with brass service fittings, evacuated system, and charged to manufacturer specifications. Verified system operation with digital manifold gauges, confirmed temperature differential across coil, and programmed thermostat controls. Integrated electrical connections into existing panel which had adequate capacity for new equipment.

Performed annual maintenance on one-year-old boiler system. Inspected electric heating elements, verified proper operation of all three parallel resistance coils, and confirmed adequate clearances and mounting integrity. System operating within normal parameters with no deficiencies noted.

Completed installation of new hot water boiler system for second floor apartment heating. Removed and replaced existing boiler with new green unit mounted on concrete pad in basement mechanical room. Installed new thermostat, expansion tank, backflow preventer/PRV combination valve, vertical air eliminator, and circulating pump. Removed obsolete ceiling-mounted expansion tank from overhead joists. Connected all components using existing 3/4 inch copper supply lines with new brass fittings and valves. Verified proper operation of all controls, tested system pressure, purged air from lines, and confirmed adequate heat delivery to second floor zone. All equipment secured and operational per manufacturer specifications.

Performed seasonal A/C start-up and system inspection. Verified unit specifications, refrigerant charge levels, and proper labeling on outdoor condensing unit. Documented equipment nameplate data including serial number, model information, electrical specifications, and refrigerant type for service records. System operational and ready for cooling season.

Responded to commercial leak complaint in women's restroom involving automatic flush toilet. Upon inspection, identified leak originating from TOTO in-wall flush valve system. Placed absorbent towels around toilet base to contain water. Inspected flush panel actuator and internal valve assembly for malfunction. Tested sensor operation and verified flush mechanism cycling. Addressed leak source and restored proper toilet function.

Conducted furnace replacement estimate for residential heating system experiencing no heat condition. Documented existing HVAC equipment installation in basement, including furnace unit, air handler, ductwork, and associated piping systems. Customer notified that required replacement parts will arrive in several days, with installation scheduled to accommodate customer's overnight work schedule.

Responded to service call for boiler estimate. Upon arrival, assessed existing heating system including Taco SR501 switching relay zone control and aging boiler unit in basement mechanical room. Documented current system configuration with copper piping connections, zone control wiring, and pressure relief valve assembly for estimate preparation.

# HVAC Service Report ## Service Performed: Gas Furnace Maintenance Completed scheduled maintenance on a 4-year-old residential gas furnace. Removed front access panel and performed comprehensive system inspection of all internal components including blower assembly, control board, ignition system, and electrical connections. Utilized digital diagnostic testing equipment to verify proper electrical readings and system performance parameters. Inspected PVC condensate drainage system and all venting connections for proper installation and function. Checked blower motor operation and verified all wire connections throughout the unit were secure and properly routed. Examined heat exchanger accessibility and overall cabinet condition. All components found operating within normal specifications with no immediate repairs required at this time.

# HVAC Install - Steam Gas Boiler Completed full steam boiler replacement in vacant residential property under financing arrangement. Coordinated asbestos abatement prior to installation to ensure safe working conditions and regulatory compliance. Removed existing boiler system and installed new steam gas boiler unit on concrete pad in basement mechanical room. Connected system to existing steam distribution piping using black iron pipe with appropriate fittings and isolation valves. Installed new backflow preventer to protect potable water supply and new automatic water feeder to maintain proper boiler water levels. Configured venting system with metallic ductwork to ensure proper combustion air supply and exhaust ventilation per manufacturer specifications and local codes. Installed new thermostat and wired to boiler controls for proper system operation. Tested all safety controls including pressure relief valve, low water cutoff, and gas valve operation. Pressurized system, check

# Service Report Responded to service call for furnace overheating complaint with system age unknown. Upon inspection, found furnace operating with burners firing continuously, as evidenced by active blue flames observed during diagnostic examination. Investigated thermostat control circuit and discovered thermostat was calling for heat excessively or failing to properly cycle the system off when set temperature was reached. Adjusted thermostat heat anticipator settings and verified proper temperature differential settings. Tested system operation through multiple heating cycles to confirm furnace now cycles on and off appropriately, maintaining comfortable temperature without overheating the home. Burner combustion pattern showed proper blue flame characteristics indicating adequate gas pressure and air mixture. All safety controls tested and operating within normal parameters. System restored to proper automatic operation with normal temperature control functionality.

Responded to service call for combustion air supply system showing signs of leakage at pipe joints. Upon inspection, found two white PVC combustion air pipes with visible water damage, staining, and wall deterioration at penetration points where pipes enter through the wall. Documented existing leak damage with photos showing brownish water stains running down wall surface from compromised pipe joints and cracking around pipe penetrations.