HVAC Services in Cleveland, OH

Conducted site assessment for mini split installation to provide heating and cooling solution. Evaluated basement utility area with exposed joists, spray foam insulation, and existing infrastructure to determine optimal equipment placement and routing for refrigerant lines and electrical connections. Documented existing conditions and building configuration to prepare comprehensive estimate with multiple system options for customer consideration.

Completed full boiler replacement in basement utility room, installing New Yorker model CG60F hot water boiler rated at 175,000 BTUs. Installation included new expansion tank, pressure reducing valve, backflow preventer, automatic air vent, and circulator pump with all associated near-boiler piping modifications using copper pipe and brass fittings. Ran new flue pipe to existing chimney connection and installed new digital programmable thermostat for system control. All components tested and operational upon completion.

Responded to service call for one-year-old furnace unit experiencing ignition failure. Customer reported unit not lighting and suspected flame sensor issues following previous maintenance visit. Performed comprehensive diagnostic inspection of all ignition system components including flame sensor, gas valve, control board, and electrical connections. Cleaned flame sensor rod to remove carbon buildup and residue that can prevent proper flame detection. Verified proper operation of inducer motor, pressure switches, and ignition sequence. Tested system through multiple heating cycles to confirm reliable ignition and flame proving. Unit operating normally with all safety controls functioning as designed upon departure.

Performed comprehensive tune-up on 20-year-old Carrier furnace operating without reported issues. Conducted combustion analysis using Testo 310 analyzer, recording CO levels at 23 ppm and temperature differential of 9.5°F, confirming safe and efficient operation. Completed full system inspection including heat exchanger examination, burner assembly cleaning, blower motor lubrication, air filter replacement, and thermostat calibration to ensure optimal performance and safety for the heating season.

Performed comprehensive tune-up on two-year-old furnace operating without reported issues. Inspected blower wheel assembly, noting dust accumulation on blades and hub, and conducted combustion analysis using diagnostic meter to verify proper system performance and temperature differentials.

Completed full hot water boiler replacement in basement utility area. Removed existing heating system and installed new Peerless model 63-06 boiler rated at 175,000 BTU. Installation included new expansion tank, pressure reducing valve, backflow preventer, automatic air vent, and circulator pump. Performed all necessary near boiler piping modifications using copper pipe to integrate new components into existing hydronic heating system. Installed new flue pipe connection to chimney for proper venting. Upgraded system controls with new digital programmable thermostat. Tested all connections for leaks, verified proper combustion and system pressurization, confirmed circulator operation, and validated thermostat functionality. System commissioned and left in full operational condition.

Performed comprehensive annual maintenance on a 3-year-old furnace system located in the basement. Conducted complete system inspection and tune-up procedures including combustion analysis using digital analyzer, which confirmed optimal operating parameters with proper O2, CO, and CO2 levels. Verified temperature differentials across heat exchanger were within manufacturer specifications. Inspected all internal components including burner assembly, ignition system, blower motor, and flame sensor. Checked all electrical connections and control wiring for proper termination and condition. Examined condensate drain system and PVC venting for proper operation and clearances. System is operating efficiently with no deficiencies noted. All safety controls tested and functioning properly.

Completed routine maintenance tune-up on a thirteen-year-old steam boiler located in basement. Performed comprehensive inspection of all system components including heat exchanger, burner assembly, and controls. Heat exchanger fins showed normal dust accumulation for unit age; cleaned and verified proper airflow through all sections. Inspected and tested all safety controls, pressure settings, and combustion parameters. System operating within manufacturer specifications with no deficiencies noted. Unit is functioning properly and ready for continued service.

Completed full installation of New Yorker model CGS50C steam gas boiler in basement mechanical room. Installation included new automatic water feeder with digital display, backflow preventer, digital programmable thermostat, and complete flue pipe assembly to chimney. All near boiler piping modifications were performed including copper supply lines, valve installations, and proper venting connections to ensure safe and efficient operation of the new steam heating system.

Responded to no heat call for 12-year-old Rheem furnace. Upon arrival, performed diagnostic inspection of unit and electrical connections, documented equipment condition with photos, and identified cause of heating failure. Restored heat to operational status and verified proper system function before departure.

Replaced compromised copper piping components including a 1-1/2" elbow, tee fitting, short nipple, and small nipple on the tee side connection. All damaged sections were removed and new fittings were installed to restore proper system integrity and prevent leaks in the heating system piping network.

Completed comprehensive heat pump and furnace tune-up maintenance service at residential property after confirming appointment scheduling. Performed full system inspection of HVAC equipment located in basement utility area, including furnace unit and HAVSCO air handling system. Conducted standard preventive maintenance procedures, verified all electrical connections, inspected ductwork connections, and ensured proper operation of both heating components for optimal winter performance.

Responded to no-heat call on 20-year-old residential furnace. Upon inspection, diagnosed failed gas valve preventing ignition sequence from completing. Removed and replaced defective gas valve with manufacturer-approved replacement part, reconnected all electrical connections and gas line, performed combustion analysis to verify proper operation, and tested unit through multiple heating cycles to confirm reliable ignition and flame sensing.

Responded to no-heat call for furnace malfunction. Upon inspection, found illuminated fault indicator on control board signaling system failure. Diagnosed failed printed circuit board (PCB) as root cause of operational issue. Replaced defective PCB with manufacturer-approved replacement part. Verified proper furnace ignition sequence, confirmed heat exchanger operation, and tested exhaust venting system for adequate draft. System restored to full operational status with all safety controls functioning correctly.

Responded to emergency service call for boiler overflow and complete loss of water supply to residence. Upon arrival, investigated 20-25 year old boiler system in basement and confirmed that automatic fill valve was left in open position, causing extensive water overflow throughout the area. Inspected plumbing connections and identified severely corroded and deteriorated pipe fittings at the water supply line that required immediate replacement. Documented extensive water damage to basement floor and walls, including moisture infiltration and degraded surfaces. Traced water supply issue and determined that main water supply had been shut off, likely as emergency response to the overflow condition. Marked failed components for replacement and provided assessment of aged plumbing infrastructure showing significant corrosion and end-of-service-life deterioration. Photographed conditions for documentation purposes.

Performed comprehensive pre-winter inspection on 12-year-old residential furnace system. Upon arrival, conducted visual assessment of unit with access panel removed to examine internal components. Inspected burner assembly, heat exchanger, blower motor, and all electrical connections. Noted operational components including gas burner rack with blue flame operation, blower assembly with motor housing, and PVC venting system with proper directional flow indicators. Examined electrical system including capacitor, contactor, and associated wiring connections. Observed evidence of significant deterioration on outdoor electrical components, including rust staining, corrosion on metal panels, and charred debris accumulation indicating previous electrical arcing or burning at contactor assembly. Documented condition of all colored wire connections (red, purple, yellow, orange, blue, green, and pink) throughout control system. Verified all safety labels and specification plates remained legib

Performed routine maintenance on a 7-year-old air handler unit located in the attic. Completed standard cooling system inspection and service procedures during the scheduled maintenance window.

Conducted on-site evaluation for commercial steam boiler replacement in industrial mechanical room. Assessed existing 2 million BTU steam boiler system, documented current equipment configuration including extensive ductwork network, insulated piping, and associated mechanical components for preparation of replacement estimate.

Completed comprehensive maintenance inspection on 20-year-old gas-powered furnace system. Performed standard heating season preventive maintenance including visual inspection of all components, burner assembly examination, heat exchanger inspection, blower motor operation check, and verification of proper venting. Inspected associated equipment including humidifier unit and filtration system, confirmed all electrical connections secure, and verified proper drainage through PVC condensate lines. System operational and ready for heating season.

Responded to service call for boiler operating at partial capacity. Upon inspection, found dual-section boiler system with one section not firing properly. Examined electrical connections, gas valves, and control systems on the affected section. Verified gas supply to both zones and inspected burner assembly access panels for proper operation. Documented equipment condition including wiring configuration, gas valve controls with identification labels, and overall system setup for further diagnostic evaluation and repair recommendations.